FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page E-7

PDF page 418 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 418
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


         (4) If § 27.903(b)(3) is selected, a spin test at 122.5 percent of the maximum
speed associated with either engine terminal speed or an overspeed limiting device
would be acceptable to show compliance. No failure should occur and distortion should
not result in fan element contact with housings or other adjacent components. (Note:
150 percent of the centrifugal force is achieved at 122.5 percent of the rotational
speed.)

      c. Turbine Engine Installation.

         (1) Explanation. The certification of turbine engines and particularly, the
qualification of turbine rotors, assumes that the limitations established during these
certifications will be accurately and rigorously observed during ground and flight
operations in an aircraft. This paragraph is intended to promote this concept.

         (2) Procedures. Primary engine limitations in the form of time, gas
temperature, torque, and rotational speed and their corresponding allowable transient
values are defined in the approved engine installation manual. The rotorcraft
manufacturer must provide reliable, accurate means to assure that these limitations are
not exceeded. These means may be in the form of automatic limiters or by crew
monitoring of appropriately marked instruments. The FAA/AUTHORITY powerplant
certification engineer and the rotorcraft manufacturer’s staff should verify these aspects
by:

                  (i)    Evaluating all applicable instrument, indicator, or warning devices,
including transmitters, and limiting devices, if any, for system tolerances.

                   (ii)   Closely reviewing the component qualification reports of items in
398c(2)(i) above to verify that these devices are properly qualified and that any
deviations are acceptable.

                    (iii)   Assuring that maintenance data is provided for functional checks and
calibration of instruments and devices which are used to monitor or protect critical
turbine rotor limitations. Preflight checks for automatic limiter devices may be
appropriate.

               (iv)   Verifying that instrument markings are clear and relatively simple, that
corresponding flight manual instructions and descriptions are straightforward and
complete, and instruments are located and orientated to minimize the probability of
reading error.

AC 27.903A.    §27.903 (Amendment 27-23) ENGINES.

     a. Explanation. Amendment 27-23 adds a requirement to § 27.903(a) that
requires reciprocating engines used in rotorcraft to be certified in accordance with the
special rotorcraft engine test requirements in § 33.49(d). This change was needed to


                                                        Page E - 7

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →