Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 3 9/30/2008
b. Engine cooling fan protection.
(1) Explanation. Section 27.903(b) is intended to provide safety to the
rotorcraft in the event of an assumed cooling fan blade failure or to prescribe a test to
show that the cooling fan blade retention means is sufficient that blade failure is not a
consideration.
(2) Procedures. The applicant may select § 27.903(b)(1), (b)(2), or (b)(3) to
show compliance with this section. If § 27.903(b)(1) is selected, a demonstration should
be conducted to show that at the maximum fan speed to be expected, a failed blade is
contained within a housing or shroud which is included in the proposed type design and
designated by the applicant as the containment shield. The rotational speed required
may be related to an overspeed limiting device or to the maximum transient speed to be
expected from analysis or test of the system or component which drives the fan. For
components driven directly by the engine, output shaft disconnect and the subsequent
terminal speed of the engine may set the test condition. To conduct an overspeed
blade failure containment demonstration, applicants have found it convenient to
progressively weaken a blade to induce failure at or above the required demonstration
speed. Blade failure may be expected to subsequently fail some or all of the remaining
blades. This condition, provided all blades are contained, is acceptable for showing
compliance with this rule. However, the corresponding loss of cooling may be
unacceptable if it causes the loss of any function essential to a controlled landing.
(3) Section 27.903(b)(2) may be selected; however, without containment,
damage to any component or structure in the plane of the fan rotor or any other
trajectory to be expected should not cause the loss of any function essential to a
controlled landing.
[The remainder of this page intentionally left blank.]
[Section AC 27.903 continued on the next page.
Page E - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.