Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
have been used during rotorcraft certification programs. FAA/AUTHORITY have
supported proposals which gave F&R test time credit for certification testing in lieu of
dedicated F&R testing. In establishing such credit, the following should be considered:
(A) The point in time in which the rotorcraft reaches substantial conformity
with the approved type design.
(B) The extent and complexity of the new design.
(C) For a previously certified rotorcraft, the F&R program requirement
should be commensurate with the modification or change in type design and may be
zero.
(ii) Historically, for major rotorcraft type certification programs, flight time
credit has been limited so as to require an irreducible minimum of 50 hours of dedicated
F&R flight time. For rotorcraft programs that involved new engine installations (mature
engine design) or drive train/rotor system changes on previously certified aircraft (TC
amendments or STC’s), flight time credit has been liberal and often resulted in very little
or no dedicated F&R testing.
b. Procedures.
(1) Type Certification Flight Tests.
(i) Prior to initiating official FAA/AUTHORITY flight tests, a conformity
inspection of the test aircraft must be accomplished. This is needed to assure that the
test aircraft is in the proper configuration or “conforms” to the engineering drawings and
documents that have been submitted to FAA/AUTHORITY, evaluated, and approved. It
is absolutely essential to know the configuration being tested in any engineering flight
evaluation. Conformity inspection prior to TIA flight tests assures that testing will not be
wasted because of configuration uncertainties.
(ii) FAA Order 8110.4A, paragraph 67, contains a requirement that the
applicant must keep the FAA/AUTHORITY advised of any configuration changes to the
aircraft. The manufacturing inspector should keep the FAA/AUTHORITY flight test pilot
apprised of any change which may affect safety of the test aircraft or may influence test
results.
(iii) Results of the conformity inspection and the engineering flight test
program must be documented. This is normally done in the Type Inspection Report
(TIR). Results may be documented in any acceptable engineering format. The report
should be in sufficient detail to clearly show how compliance with each appropriate
section of the rules was determined.
(iv) The flight test pilot must assure that the FAA/AUTHORITY
manufacturing inspector and certification engineer are aware of all configuration
Page FAR 21 - 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.