Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
sight gauges or dip sticks, filler ports and drain valves for engines, auxiliary propulsion
units, transmissions, fuel tanks and filters, etc.
(iv) Electrical interconnections to prevent difference of potential should be
provided in the form of grounding straps or wires sized to carry the currents to be
expected. Verify that the attachments for these grounding devices are not
compromised by paint or zinc chromate which will tend to electrically insulate the engine
or component. Note that engine mount structure should not be accepted as a
grounding device since electrical current will cause corrosion at attach points.
(v) Axial and radial expansion of turbine engines is usually not a problem
unless redundant mount arrangements are used. Special expansion provisions are
usually required if engine components other than mounting points are attached to
bulkheads, firewalls, other engines, or drive system components. Engine output shaft
axial or bending loads due to thermal expansion and to deflection of supports under
ground or flight loads should be checked. Other components of concern are
compressor inlet flanges, exhaust ducts, and rigid fluid or air lines between aircraft
structure and the engine. The engine installation data will provide limit loads to be
considered for parts of the engine which normally are attached to airframe components.
c. Section 27.901(c).
(1) Explanation. Paragraph (c), in conjunction with the installation manual
requirements of § 33.5, is intended to assure compliance with the detail installation
requirements developed by the engine manufacturer to assure safe, continued
operation of the engine.
(2) Procedure. Compliance with most of the detail requirements in the engine
installation manual can be established by test or by design features and arrangements
negotiated between the rotorcraft manufacturer and the FAA/AUTHORITY powerplant
engineer. Some aspects, usually involving inlet and/or exhaust distortion limitations,
vibration limitations and aircraft/engine interface items may require direct assistance
and information from the engine manufacturer to determine that compliance with the
installation manual exists. Fuel control/engine/rotor system torsional matching is
usually a developmental problem to be worked out before presentation of the rotorcraft
to the FAA/AUTHORITY; however, final flight tests for surge or stall, torsional stability,
and acceleration/ deceleration schedules may require direct coordination among
FAA/AUTHORITY installation engineers, engine manufacturers’ representatives, and
the FAA/AUTHORITY engine certification engineers. Reciprocating, carburetor
equipped engines usually require a particular carburetor configuration to achieve
adequate engine cooling. This configuration, identified as a “carburetor parts list,” must
be approved for the engine under Part 33 and should be listed on the type data sheet
for the rotorcraft.
Page E - 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.