FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-130

PDF page 403 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 403
AC 27-1B · D-130Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                       2/4/2016


                (ii) Cable length and marking. A length of cable nearest the cable's
attachment to the hoist drum should be visually marked to indicate to the operator that
the cable is near full extension. The length of cable to be marked is a function of the
maximum extension speed of the system and the operator's reaction time needed to
prevent cable run out.  It should be determined during certification demonstration tests.
In no case should the length be less than 3-1/2 drum circumferences.

                 (iii) Cable stops. Means should be present to automatically stop cable
movement quickly when the system's extension and retraction operational limits are
reached.

          (10) Section 27.865(c)(2) PCDS. For all HEC applications, an approved
PCDS is required. The PCDS may be either previously approved or is required to be
approved during certification. A PCDS may also be approved after the external load
system certification. Including a limitation in the RFM or RFMS requiring an approved
PCDS will permit more flexibility for operators to utilize their own approved PCDS (see
paragraph d.(4) of this guidance). In either case, its compatibility with the helicopter
should be approved.

Note: PCDS designs can vary from simple single occupant lifesaving devices to
        relatively complex multiple occupant cages or gondolas. The purpose of the
    PCDS is to provide a minimum acceptable level of safety for personnel being
       transported outside the rotorcraft. The personnel being transported may be
       healthy or injured, conscious or unconscious.

               (i) TSO C167 is an approved minimum performance specification for HEC
body harnesses.

                (ii) Static strength. The PCDS should be substantiated for the allowable
ultimate load and loading conditions as determined under paragraph d.(6) above.

                 (iii) Fatigue. The PCDS should be substantiated for fatigue as determined
under paragraph d.(6) above.

             (iv) Personnel safety. For each PCDS design, the applicant should submit a
design evaluation that assures the necessary level of personnel safety is provided. As
a minimum, the following should be evaluated.

              (A) The PCDS should be easily and readily ingressed or egressed.

              (B) It should be placarded for proper capacity, internal arrangement and
location of occupants, and ingress and egress instructions.

             (C) For door latch fail-safety, more than one fastener or closure device
should be used. The latch device design should provide direct visual inspectability to
assure it is fastened and secured.


Page D - 130

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →