Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
demonstrate that the test squibs (that are more EMI sensitive than the squibs specified
for use in the QRS) do not inadvertently operate during the test.
(viii) Section 27.865(c)(3) Placarding and marking. For jettisonable HEC
applications, the associated QRS placarding should be given special consideration to
assure the proper level of occupant safety.
(8) Cargo hooks or equivalent devices and their related systems. All cargo hooks
or equivalent devices should be approved to acceptable aircraft industry standards.
The applicant should present these standards, and any related manufacturer’s
certificates of production or qualification as part of the approval package.
(i) General. Cargo hook systems should have the same reliability goals and
should be functionally demonstrated under critical loads for NHEC and HEC, as
appropriate. All engagement and release modes should be demonstrated. If the hook
is used as a quick-release device, then release of critical loads should be demonstrated
under conditions that simulate maximum allowable bank angles and speeds and any
other critical operating conditions. Demonstration of any re-latching features and any
safety or warning devices should also be conducted. Demonstration of actual in-flight
emergency quick-release capability may not be necessary if the quick-release capability
can be acceptably simulated by other means.
Notes: Cargo hook manufacturers specify particular shapes, sizes, and cross
sections for lifting eyes to assure compatibility with their hook design (e.g.,
Breeze Eastern Service Bulletin CAB-100-41). Experience has shown that,
under certain conditions, a load may inadvertently hang up because of
improper geometry at the hook-to-eye interface that will not allow the eye to
slide off an open hook as intended.
For both NHEC and HEC designs, the phenomena of hook dynamic roll-out
(inadvertent opening of the hook latch and subsequent release of the load)
should be considered to assure that QRS reliability goals are not
compromised. This is of particular concern for HEC applications. Hook
dynamic roll-out occurs during certain ground handling and flight conditions
that may allow the lifting eye to work its way out of the hook.
Hook dynamic roll-out typically occurs when either the RLCs sling or harness
is not properly attached to the hook, is blown by down draft, is dragged along
the ground or through water; or is otherwise placed into the dangerous hook-
to-eye configuration.
The potential for hook dynamic roll-out can be minimized in design by
specifying particular hook-and-eye shape and cross-section combinations.
For non-jettisonable RLCs, a pin can be used to lock the hook keeper in place
during operations.
Page D - 127
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.