FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-123

PDF page 396 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 396
AC 27-1B · D-123Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                       AC 27-1B, Chg 7


Note:  If the HEC is engaged in work tasks that employ devices of significant added
      weight (heavy backpacks, tools, fire extinguishers, etc.), the total weight of the
      223-pound man and equipment should be assumed in the structural analysis or
        test.

                 (iii) Critical Structural Case. For applications involving more than one RLC
class or cargo type, the structural substantiation is required only for the most critical
case. The most critical case should be determined by rational analysis.

             (iv) Jettisonable Loads. For the substantiating analyses or tests of all
jettisonable RLC external loads, including HEC, the maximum external load should be
applied at the maximum angle that can be achieved in service but not less than
30 degrees. The angle should be measured from the sling-load-line to rotorcraft vertical
axis (z axis) and may be in any direction that can be achieved in service. The
30-degree angle may be reduced in some or all directions if it is impossible to obtain
due to physical constraints or operating limitations. The maximum allowable cable
angle should be determined and approved. The angle approval should be based on
structural requirements, mechanical interference limits, and flight handling
characteristics over the most critical conditions and combinations of conditions in the
approved flight envelope.

            (v) Hoist system limit load.

Note: In cases where hoist cables or long line cables are utilized, a new dynamic
      system is established. Characteristics of the system should be evaluated to
      assure that either no hazardous failure modes exist or that they are acceptably
      minimized. For example, the cable or long line may exhibit a natural frequency
       that could be excited by sources internal to the overall structural system (i.e., the
        rotorcraft) or by sources external to the system. Another example is the loading
       effect of the cable acting as a spring between the rotorcraft and the suspended
       external load.

              (A) Determine the basic loads that result in the failure or unspooling of the
hoist or its installation, respectively.

Note: This determination should be based on static strength and any significant
      dynamic load magnification factors.

              (B) Select the lower of the two values as the ultimate load of the hoist
system installation.

             (C) Divide the selected ultimate load by 1.5 to determine the true structural
limit load of the system.




                                                         Page D - 123

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →