FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-122

PDF page 395 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 395
AC 27-1B · D-122Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                       2/4/2016


Note: In cases where NHEC or HEC can have more than one shape, center-of-gravity,
        center-of-lift, or be carried at more than one distance in flight from the rotorcraft
      attachment, a critical configuration for certification purposes may not be
      determinable.  If such a critical configuration can be determined, it may be
      examined for approval as a "worst case" to satisfy a particular certification
        criterion or several criteria, as appropriate.  If such a critical configuration cannot
     be determined, the extreme points of the operational – external load
       configuration envelope should be examined with consideration given to any other
       points within the envelope which experience or other rationale would indicate
      should be investigated.

                (ii) Vertical Limit and Ultimate Load Factors. The basic NZW is converted to
ultimate load by multiplying the maximum vertical limit load by the appropriate safety
factor. (For restricted category approvals, see section AC 27 MG 5 of this AC.) This
ultimate load is used to substantiate all existing structure affected by, and all added
structure associated with, the load carrying device, its attachments and its cargo.
Casting factors, fitting factors, and other dynamic load factors should be applied where
appropriate.

              (A) NHEC applications. In most cases, it is acceptable to perform a
standard static analysis to show compliance. A vertical limit load factor (NZW) of 2.5 g is
typical for heavy gross weight NHEC hauling configurations (see section 27.337 of this
guidance). This vertical load factor should be applied to the maximum external load for
which application is being made, together with a minimum safety factor of 1.5.

              (B) HEC applications.

                  (1) If a safety factor 3.0 or more is used, it is acceptable to perform a
standard static analysis to show compliance. The safety factor should be applied to the
yield strength of the weakest component in the system (QRS, PCDS, and attachment
load path).  If a safety factor of less than 3.0 is used, both an analysis and a full-scale
ultimate load test of relevant parts of the system should be submitted.

                  (2) Since HEC applications typically involve lower gross weight
configurations, a higher vertical limit load factor is required to assure that limit load is
not exceeded in service. The applicant should use either the conservative value of 3.5
g or an analytically derived maximum vertical limit load factor for the requested
operating envelope. Linear interpolation between the vertical load factors of maximum
and minimum design weights may be used. However, in no case may the vertical limit
load factor be less than 2.5 g for any RLC application for HEC.

                  (3) For the purpose of structural analysis or test, assume a 223-pound
(101 Kg) man as the minimum weight of each occupant carried as HEC.




Page D - 122

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →