Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
• This external load system does not include equipment to allow
direct intercommunication among required crewmembers and
external occupants. Operating this external load equipment with
HEC is not authorized unless equipment to allow direct
intercommunication among required crewmembers and external
occupants is approved by the local Aviation Authority.
(iii) Additional RFM or RFMS requirements are contained within each
applicable paragraph of this guidance.
(5) Continued airworthiness.
(i) Instructions for Continued Airworthiness. Maintenance manuals (and RFM
supplements) developed by applicants for external load applications should be
presented for approval and should include all appropriate inspection and maintenance
procedures. The applicant should provide sufficient data and other information to
establish the frequency, extent, and methods of inspection of critical structure, systems,
and components. 14 CFR 27.1529 and Appendix A to part 27 requires this information
be included in the maintenance manual. For example, maintenance requirements for
sensitive QRS squibs should be carefully determined, documented, approved during
certification, and included as specific mandatory scheduled maintenance requirements
that may require either "daily" or "pre-flight" checks (especially for HEC applications).
(ii) Hoist system continued airworthiness. The design life of the hoist system
and any limited life components should be clearly identified, and the Airworthiness
Limitations Section of the maintenance manual should include these requirements. For
STCs, a maintenance manual supplement should be provided that includes these
requirements.
Note: Design lives of hoist and cable systems are typically between 5,000 to 8,000
cycles. Some hoist systems have usage time meters installed. Others may have
cycle counters installed. Cycle counters should be considered for HEC
operations and high load or other operations that may cause low-cycle fatigue
failures.
(6) Section 27.865(a) Static Structural and § 27.865(f) Fatigue Substantiation
Procedures. The following static structural substantiation methods and fatigue
substantiation procedures should be used:
(i) Critical basic load determination. The critical basic loads and
corresponding flight envelope are determined by statically substantiating the gross
weight range limits, the corresponding vertical limit load factors (NZW) and safety factors
applicable for the type of external load for which the application is being made.
Page D - 121
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.