Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
(E) QRS reliability (i.e., failure modes) affecting flight performance. The
FHA of the QRS (see paragraph d.(2) above) should show that any single system failure
will not result in unsatisfactory flight characteristics, including any QRS failures resulting
in asymmetric loading conditions.
(F) Flight test weight and CG locations. All flight tests should be
conducted at the extreme or critical combinations of weight and longitudinal and lateral
CG conditions within the applied for flight envelope. Typically the two load conditions
would be a heavy weight and low area cargo, and a low weight and high area cargo.
The rotorcraft should remain within approved weight and CG limits both with the
external load applied and after jettison of the load.
(G) Jettison Envelopes. Emergency and normal jettison demonstrations
should be performed at sufficient airspeeds and descent rates to establish any
restrictions for satisfactory separation characteristics. Both the maximum and minimum
airspeed limits and maximum descent rate for safe separation should be determined.
The sideslip envelope as a function of airspeed should be determined.
(H) Altitude. Emergency and normal jettison demonstrations should be
performed at altitudes consistent with the approvable operational envelope and with the
maneuvering requirements necessary to overcome any adverse effects of the jettison.
(I) Attitude. Emergency and normal jettison demonstrations should be
performed from all attitudes appropriate to normal and emergency operational usage.
Where the attitudes of HEC or NHEC with respect to the helicopter may be varied, the
most critical attitude should be demonstrated. This demonstration would normally be
accomplished by bench testing.
(4) Rotorcraft Flight Manual (RFM) and Rotorcraft Flight Manual Supplement
(RFMS):
(i) General.
(A) Present appropriate flight manual procedures and limitations for all
HEC operations.
(1) Approval of an external loads equipment design in accordance with
§ 27.865 does not provide approval to conduct external loads operations. Therefore,
the following shall be included as a limitation in the RFM or RFMS:
• The external load equipment certification approval does not
constitute operational approval; operational approval for external
load operations must be granted by the local Aviation Authority.
Page D - 119
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.