Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
Note: Some hoist designs have built-in cable tensioning devices that function at the no
load-speed combination, as well as at other load-speed combinations. This
device should work during the no load-speed and other load-speed cable-cutting
demonstrations.
(E) Any devices or methods used to increase the mechanical advantage of
the hoist should also be demonstrated.
(F) During a portion of each demonstration cycle, the hoist should be
operated from each station from which it can be controlled.
(ii) Hoist and rescue hook systems or cargo hook systems flight test. An in-
flight demonstration test of the hoist system should be conducted for helicopters
designed to carry NHEC or HEC. The rotorcraft should be flown to the extremes of the
applicable maneuver flight envelope and to all conditions that are critical to strength,
maneuverability, stability, and control, or any other factor affecting airworthiness.
Unless a lesser load is determined to be more critical for either dynamic stability or
other reasons, the maximum hoist system rated load or, if less, the maximum load
requested for approval (and the associated limit load data placards) should be used for
these tests. The minimum hoist system load (or zero load) should also be
demonstrated in these tests.
(iii) Section 27.865(d) Flight test Verification Work. Flight test verification
work that thoroughly examines the operational envelope should be conducted with the
external cargo carriage device for which approval is requested (especially those that
involve HEC). The flight test program should show that all aspects of the operations
applied for are safe, uncomplicated, and can be conducted by a qualified flight crew
under the most critical service environment and, in the case of HEC, under emergency
condition. Flight tests should be conducted for the simulated representative NHEC and
HEC loads to demonstrate their in-flight handling and separation characteristics. Each
placard, marking, and flight manual supplement should be validated during TIA flight
testing.
(A) General. Flight testing or an equivalent combination of analysis,
ground tests, and flight tests should be conducted under the critical combinations of
configurations and operating conditions for which basic type certification approval is
sought. The critical load condition of the intended cargo (e.g. rocks, lumber, radio
towers, HEC) may be defined by a heavy weight and low area cargo or a low weight
and high area cargo. The effects of these load conditions should be evaluated
throughout the operational aspects of cargo loading, take-off, cruise up to maximum
allowable speed with cargo, jettison, and landing. The helicopter handling with different
cable conditions should include lateral transitions and quick stops up to the helicopter
approved low airspeed limitations. Additional combinations of external load and
operating conditions may be subsequently approved under relevant operational
requirements as long as the structural limits and reliability considerations of the basic
certification approval are not exceeded (i.e., equivalent safety is maintained). The
Page D - 117
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.