FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-116

PDF page 389 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 389
AC 27-1B · D-116Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                       2/4/2016


application requires more than one hoist cycle per flight, then the number of
demonstration cycles should be increased accordingly by multiplying the test cycles with
the intended higher cycle number per flight. These repetitive tests may be conducted
on the rotorcraft or by using a bench simulation that accurately replicates the rotorcraft
installation.

              (F) An environmental qualification for the proposed operating environment.
This review includes consideration of low and high temperatures (typically -40F to
+150F), altitudes to 12,000 feet, humidity, salt spray, sand and dust, vibration, shock,
rain, fungus, and acceleration. The FAA has accepted the results from the appropriate
rotorcraft sections of RTCA Document DO-160 for high and low temperature and
vibrations. The environmental qualification will address icing for those external load
systems installed on rotorcraft approved for flight into icing conditions.

            (G) Qualification of the hoist itself to the appropriate electromagnetic
interference (EMI) and lightning threat levels specified for NHEC or HEC, as applicable.
This qualification can occur separately or as part of the entire onboard QRS.

       (3) Testing.

               (i) Hoist system load-speed combination ground tests. The load versus
speed combinations of the hoist should be demonstrated on the ground (either using an
accurate engineering mock-up or a rotorcraft) by showing repeatability of the no load-
speed combination, the 50 percent load-speed combination, the 75 percent load-speed
combination, and the 100 percent (i.e., system rated limit) load-speed combination.  If
more than one operational speed range exists, the preceding tests should be performed
at the most critical speed.

              (A) At least 1/10 of the hoist demonstration cycles (see definition) should
include the maximum aft angular displacement of the load from the vertical, applied for
under § 27.865(a).

              (B) A minimum of six consecutive, complete operation cycles should be
conducted at the system's 100 percent (i.e., system limit rated) load-speed combination.

             (C) In addition, the demonstration should cover all normal and emergency
modes of intended operation and should include operation of all control devices such as
limit switches, braking devices, and overload sensors in the system.

             (D) All quick disconnect devices and cable cutters should be
demonstrated at 0 percent, 25 percent, 50 percent, 75 percent, and 100 percent of
system limit load or at the most critical percent.





Page D - 116

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →