FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-109

PDF page 382 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 382
AC 27-1B · D-109Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                      AC 27-1B, Chg 4


             SUBPART D - DESIGN AND CONSTRUCTION

                       EXTERNAL LOAD.


AC 27.865.  § 27.865 (Amendment 27-11) EXTERNAL LOAD ATTACHING MEANS.

     a. Explanation.

         (1) If certification for external load operations is requested, the rule requires
that the external load attaching means be substantiated by test or analysis for a limit
static load equal to or greater than 2.5 times the maximum external load for which
certification is requested. The factor of 2.5 times the maximum external load was
established as a minimum strength requirement by Part 133 operations to account for
loading effects of sling-load angles up to 30° from the vertical. Allowance for reducing
the 30° angle is provided if substantiated.

         (2) The rule requires that a quick-release device be installed on one of the
pilot’s primary controls so the pilot can quickly release the external load during an
emergency situation. In addition, a backup manual mechanical control for the
quick-release device is required to be readily accessible to either the pilot or another
crewmember.

         (3) The rule requires appropriate placards or markings stating the maximum
authorized external load.

     b. Procedures.

         (1) The maximum external load for which authorization is requested should not
exceed the rated capacity of the quick-release device. The quick-release device should
be strength tested (with FAA/AUTHORITY witness) if it is not produced to a recognized
industry or military standard.

         (2) Substantiation of external loading requirements must include any direction
making an angle of 30° (with the exception of directions having a forward component).
(reference § 27.865(a).)

                  (i)   The sling-load angle (i.e., the angle between the vertical direction and
the sling-load cable supporting the external load) should not exceed an angle of 30° to
minimize the cable tension load.

                   (ii)   The 30° angle may be reduced if an operating limitation is established
limiting external load operations to such angles for which compliance has been shown
or if the reduced angle cannot be exceeded in service. The lesser angle should be
substantiated by flight testing.



                                                         Page D - 109

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →