Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 2 4/25/06
(3) The external load releasing system is specified to include a quick release
device installed on one of the pilot’s primary controls. It is usually installed on the cyclic
stick to allow the pilot to release the load with minimum distraction after maneuvering
the load into the release position.
(4) A manual mechanical control for the quick-release device is specified to be
installed and be readily accessible to the pilot or to another crewmember. A sufficient
amount of slack should be provided in the control cable to permit complete cargo
movement without tripping the cargo release.
AC 27.865A. § 27.865 (Amendment 27-26) EXTERNAL LOAD ATTACHING
MEANS.
a. Explanation. Amendment 27-26 added two requirements to § 27.865:
(1) Section 27.865(a) is clarified to allow use of a design factor less than 2.5g’s,
for rotorcraft load combinations A, B, and C non-human external cargo applications
provided the lower load factor is not likely to be exceeded by virtue of the rotorcraft
characteristics and capability. That is, the rotorcraft design factors may be used for the
cargo device system.
(2) Section 27.865(d) was added to clarify and specify the fatigue requirements
for the external cargo attaching means.
b. Procedures. All of the policy material pertaining to this section remains in effect
with the following additions:
(1) For § 27.865(a), if a design limit load factor less than 2.5g’s is requested,
the applicant should provide a rational analysis and/or a flight operations data base that
clearly shows that the load factor requested is unlikely to be exceeded in service.
NOTE: § 27.337(b) requires use of 2.0 g’s as a minimum.
(2) § 27.865(d), all failures of the cargo attaching means (and the
associated critical components) that are likely to be hazardous to the rotorcraft
should be identified by an acceptable means, such as a Failure Mode Effect
Analysis (FMEA). The critical components associated with these failure modes
should receive a fatigue analysis and/or test to ensure that the likelihood of a
failure occurring is minimized. In the majority of cases, an analysis using the
methods of AC 27 MG 11, “Fatigue Evaluation of Rotorcraft Structure”, will be
sufficient. If any component has a service life and/or mandatory inspection these
components and each mandatory life should be identified, approved, and placed
in the airworthiness limitations section of the maintenance manual or Instructions
for Continued Airworthiness. See paragraph AC 27.1529 for information on
these manuals.
Page D - 110
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.