FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-107

PDF page 380 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 380
AC 27-1B · D-107Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                            AC 27-1B


     b. Procedures.

         (1) A part of acceptable geometry made of steel, or another fireproof material,
may be used to comply with the standard.

         (2) A material system, panel, or assembly would be equivalent to steel provided
it successfully completes the flammability tests described in
paragraph AC 27.861b(3)(vi), for Category B rotorcraft adjusted for the time period
appropriate to the rotorcraft application.

         (3) It is appropriate to further define “fire resistant.” A material system, panel,
or assembly would be equivalent to aluminum (fire resistant) if it successfully completes
the following flammability test. Locate a specimen (approximately 8 inches square) of
the material system panel, assembly, or part at approximately a 45° angle to a
horizontal line. Apply the limit or normal operating load. Impinge a 2000 ±150° F
(1093 ± 83°C) flame on the article for at least 5 minutes duration. Flame penetration of
the test article is not allowed. In addition, the part or component should be able to
perform its intended function, as installed, during and after the test.

AC 27.863  § 27.863 (Amendment 27-16) FLAMMABLE FLUID FIRE
PROTECTION.

     a. Background.

         (1) The development of § 27.863 can be traced through CARs 6.485 and 6.486,
and subsequent Amendment 27-16.

         (2) Investigation of several accidents disclosed evidence of in-flight fires
caused by leakage of flammable fluids to ignition sources. The revisions to § 27.863
adopted by Amendment 27-16 require significantly more attention to overall fire
protection and prevention.

     b. Explanation.

         (1) Prior to Amendment 27-16, this rule only required either a means to prevent
ignition of flammable fluids or vapors or a means to control any resulting fire. Isolation
of flammable fluids and vapors from ignition sources by shrouding or sealing was the
normal method of compliance. With Amendment 27-16, the rule further requires the
assumption that these means fail or are ineffective and a fire does occur. Means to
minimize the consequence of these fires must be provided. Specifically identified
considerations must include the flammability of any combustible or absorbing materials,
electrical faults, malfunction of protective devices, and so forth.

         (2) The rule does not require the entire rotorcraft to be a “designated fire zone.”



                                                         Page D - 107

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →