FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-106

PDF page 379 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 379
AC 27-1B · D-106Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

                   (ii)   The factors affecting the time interval should include the maximum
height above the terrain, the maximum operating altitude, the flight manual
recommendations for rate of descent, and a reasonable time for recognizing a
powerplant fire.

                    (iii)  The factors affecting the change in physical characteristics (strength
primarily, but stiffness may also be a factor) of the parts are the temperature of the part,
time interval at the elevated temperature, size, and heat absorption or rejection.

               (iv)  The factors affecting the temperature of the part are location and
distance from the fire and flames and temperature of the flames (2,000° F ±50° F should
be used unless proven to be inapplicable).

              (v)  The rule requires substantiations for any foreseeable powerplant fire
condition. Each rotorcraft design is unique and an evaluation of each design is
necessary to establish the fire and flight conditions under consideration.

               (vi)  A very brief and simple example of compliance noted here may be
helpful. This example pertains to a single-engine rotorcraft with the engine mounted on
top at the fuselage centerline. The engine is supported by all steel tubular mounts. The
fuselage panel serves as a work deck as well as a firewall. A 15-minute duration is
appropriate for this design. A representative panel of the firewall (deck) skin may be
subjected to the autorotational flight loads and the landing load. A flame from an
appropriate-sized burner, measuring 2,000° F ±50° F at the skin surface, should
impinge on the loaded panel for 15 minutes. The panel may deform but must remain
intact and sustain the appropriate load. The flame should not penetrate the panel skin.

                (vii)  Other rotorcraft designs may have engines located on top of the
fuselage under the main rotor.  If cowls or firewalls do not isolate the rotors and
essential controls, it must be determined by a rational analysis or by temperature
measurement that the rotor and essential controls will perform their functions. Air flow
through the rotor and factors noted in paragraphs AC 27.861b(3)(ii), (3)(iii), and (3)(iv)
are important to an analysis.

AC 27.861A  § 27.861 (Amendment 27-26) FIRE PROTECTION OF STRUCTURE,
          CONTROLS, AND OTHER PARTS.

     a. Explanation.

         (1) Amendment 27-26 revised the regulation to allow use of parts made from
standard fireproof materials of known acceptable dimensions in areas affected by
powerplant fires without further proof or qualification. Previously, the standard imposed
a performance criteria regardless of the materials and part dimensions used.

         (2) “Fireproof” and “fire resistant” are defined in FAR Part 1, § 1.1.



Page D - 106

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →