FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-104

PDF page 377 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 377
AC 27-1B · D-104Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


         (8) For compliance with § 27.859(h), each combustion and ventilating air
intake’s location should be identified, reviewed, and tested to ensure that no flammable
fluids or vapors can enter the heater system, ignite and create a fire.  If a combustion or
ventilating air intake’s location is critical or questionable, it should be relocated,
shielded, drained, or other equivalent means provided to eliminate the potential fire
hazard.  If engineering analysis and evaluation are not adequate to make an acceptable
safety finding, testing using dyed, inert, leaked fluids or vapors should be conducted.

         (9) For compliance with § 27.859(i), each heater exhaust system design should
be reviewed, tested, or a combination to ensure proper compliance with § 27.1121 and
§ 27.1123 (reference AC paragraphs AC 27.1121 and AC 27.1123, respectively). Each
exhaust shroud should be sealed to ensure that leaked flammable fluids or vapors do
not contact the hot exhaust and cause a fire. The seal design should be reviewed to
ensure that the sealing material is fireproof, is chemically compatible with the relevant
fuels and vapors, is durable and is functionally adequate.  If the design review is not
conclusive for compliance purposes, then the seal system should be bench tested
under pressure while undergoing critical service loads and motions to ensure no
leakage occurs. An analysis should be conducted to determine the structural effects on
the exhaust system of the worse case restricted backfire (typically a shock wave
analysis can be used to determine the peak internal pressure and, the resultant load on
the exhaust system.)  If structural failure would occur, based on the analysis, either the
backfire restriction should be reduced or the exhaust design should be structurally
improved to eliminate the failure.

        (10) For compliance with § 27.859(j), each heater’s fuel system design must be
reviewed to ensure that compliance with the powerplant fuel system requirements of
Part 27 that are necessary for safe operation to be achieved. An equivalent safety
finding should be made if an application is received that requests partial compliance or
non-compliance with the powerplant fuel system requirements of Part 27. The finding
should ensure that the safety intent of § 27.859(j) is achieved. Analysis, engineering
evaluation, testing, or a combination should be used to substantiate the heater fuel
system design. Heater fuel system components that, by leakage or other failures, can
induce flammable fluids or vapors into the ventilating air stream should be shrouded by
drainable, fireproof shrouds.

        (11) For compliance with § 27.859(k), the drain system design should be
reviewed to identify parts that may be subjected to high temperature and parts that may
be subjected to hazardous ice accumulation in service. The high temperature parts
should be evaluated using the methods of compliance for heater exhausts (reference
paragraph AC 27.859b(9), above and paragraph AC 27.1123). Drains that would be
stopped up from ice accumulation should be protected by relocation, size, shields,
heating, or a combination to ensure hazardous fluids and vapors are properly drained
away.




Page D - 104

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →