FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-103

PDF page 376 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 376
AC 27-1B · D-103Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

and/or flight test work with dyed, inert fluids or vapors should be conducted to
accurately display discharge patterns.

         (4) For compliance with § 27.859(d), the ventilating air duct design should be
reviewed to determine what ducts are routed through heater zones. Once this has been
determined, each duct section running through the heater zone should be made
fireproof by either using a fireproof shroud around the existing duct or by using fireproof
material for the duct wall.

         (5) For compliance with § 27.859(e), any design using combustion air ducts
should be reviewed to ensure that the ducts are either made from fireproof material or
shrouded with a fireproof shroud over a safe distance (see definition). The safe
distance should be determined analytically, by test, or a combination, if the analytical
results are not conclusive. The design should be reviewed to ensure that combustion
air ducts are not connected to the ventilating air stream, except when an equivalent
safety finding can be made that shows backfires or reverse burning cannot induce
flames or fumes into the ventilating air stream under any failure condition or malfunction
of the heater or its associated components. Such a finding should require analysis,
testing, or a combination for a proper determination.

         (6) For compliance with § 27.859(f), the design and installation of all standard
control components, control tubing and safety controls should be reviewed to determine
the probable points of water or ice accumulation (e.g., sumps, rough surfaces, joints,
etc.)  If a design review cannot accurately determine these accumulation points, then
bench tests and flight tests should be conducted for proper determination. Once these
points are identified, the ability of the effected part (or parts) to perform its intended
function when water or ice has fully accumulated must be determined for both normal
and failure conditions.  If the part (or parts) either has not lost its ability to function: has
lost only part of its ability to function; or has lost all of its ability to function; and the
entire system’s function is not impaired, then nothing further should be required.
However, if the overall system’s function is hazardously impaired or lost, as a result of
water or ice accumulation on a part (or parts), then rectifying design improvements
should be made prior to final approval. These improvements should either alter the
part’s environment (e.g., relocation, enclosure, insulation, etc.) or eliminate the
hazardous accumulation of water or ice (e.g., provide drainage, better sealing, better
location, different surface finish, etc.).

         (7) For compliance with § 27.859(g), combustion heaters, if used, must have
separate, independent safety controls from their standard controls (e.g., air
temperature, air flow, fuel flow, etc.) which are remotely located in case of a heater fire,
are operable by the crew and automatically shut off the ignition and fuel supply when a
hazardous condition exists (as defined by § 27.859(g)). These separate safety controls
must comply with § 27.859(g)(1), must keep the heater off until restarted by the crew or
ground maintenance, and must warn the crew when an essential heater is automatically
shut down. The safety control system design should be thoroughly reviewed and tested
to ensure that it complies and that no hazardous failure modes exist.


                                                      Page D - 103

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →