FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-101

PDF page 374 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 374
AC 27-1B · D-101Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


AC 27.859  § 27.859 (Amendment 27-23) HEATING SYSTEMS.

     a. Explanation. This regulation ensures that onboard heating systems (of all type
designs) are safe during normal and survivable emergency operations. Thus, as a
minimum, each heating system type design must meet the applicable requirements of
§ 27.859.

     b.  Definitions.

         (1) Backfire. An improperly timed detonation (or explosion) of a fuel mixture
which results in higher than normal temperatures and pressures.

         (2) Reverse flame propagation. An event that occurs when the flame from a
controlled combustion process (such as a heater) goes in an abnormal path (i.e., either
a reverse or different path than the intended path) as a result of a change in internal
pressure or internal pressure gradient (e.g., a backfire) from a detonation or a similar
event.

         (3) Safe distance. A maximum flow length dimension determined from the
thermodynamics of a worse case flow reversal (backfire) and the local heater system
geometry.

         (4) Heater zone (or region). A geometric zone defined by the heater type,
heater size, location of heater system components, and the maximum safe distance
determined under (3) above. The heater system components may affect the heater
zone’s size if they are closely located to the heat source. For example a heater fuel
tank would not be part of the heater zone if it were located far away from the zone
boundary; however, if it were adjacent or close to the boundary, it would be included in
the heater zone.

         (5) Fireproof. Fireproof is defined in § 1.1 “General Definitions.”

         (6) Severe Fire. The following thermodynamic definitions are based on
AC 20-135, “Powerplant Installation and Propulsion System Component Fire Protection
Test Methods, Standards, and Criteria” and on the definitions in § 1.1 for fire resistant
and fireproof materials. These definitions are provided for analytical purposes. A
severe fire, when used with respect to fireproof materials, is one which reaches a
steady state temperature of 2,000 ±150° F for at least 15 minutes. A severe fire, when
used with respect to fire resistant materials, is one which reaches a steady state
temperature of 2,000 ±150° F for at least 5 minutes.

         (7) Hazardous accumulation of water or ice. An accumulation of water or ice
that causes a device to not perform its intended function in either normal operation or a
survivable emergency situation.



                                                      Page D - 101

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →