FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-87

PDF page 360 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 360
AC 27-1B · D-87Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                        AC 27-1B, Chg 2

Other methods of substantiation may be acceptable depending upon the particular
design of the flotation system.

              (B) Structural Integrity. The flotation bags should be evaluated for loads
resulting from:

               (1) Airloads during inflation and fully inflated for the most critical flight
conditions and water loads with fully inflated floats during water impact for the water
entry conditions established under paragraph AC 27.801(b)(1)(ii) for rotorcraft desiring
float deployment before water entry; or

               (2) Water loads during inflation after water entry.

             (C) Handling Qualities. Rotorcraft handling qualities should be verified to
comply with the applicable regulations throughout the approved operating envelopes
for:

               (1) The deflated and stowed condition;

               (2) The fully inflated condition; and

               (3) The in-flight inflation condition. For float systems which may be
inflated in flight, rotorcraft controllability should be verified by test or analysis assuming
the most critical float compartment fails to inflate.

         (3) Flotation and Trim. The flotation and trim characteristics should be
investigated for a range of sea states from zero to the maximum selected by the
applicant and should be satisfactory in waves having height/length ratios of 1:12.5 for
multiengine rotorcraft with Category A engine isolation and 1:10 for all other rotorcraft.
Model tests in a wave basin on a number of different rotorcraft types have indicated that
an improvement in sea keeping, response of the rotorcraft to waves, performance of
approximately one sea state can consistently be achieved by fitting float scoops.  If the
basic flotation system (without scoops) has demonstrated compliance with the minimum
flotation and trim requirements, credit for float scoops to achieve stability in more severe
water conditions may be allowed. However, the effect of scoops on improved sea
keeping must be demonstrated during model testing.

                  (i)    Flotation and trim characteristics should be demonstrated to be
satisfactory to at least sea state 4 conditions.

                   (ii)   Flotation tests should be investigated at the most critical rotorcraft
loading condition.





                                                       Page D - 87

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →