Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
type certificate or a field approval. Compliance with the ditching requirements should be
reviewed after any interior configuration changes and limitations changed where
applicable.
(iii) The Rotorcraft Flight Manual and supplements deserve special
attention if a “segmented” certification procedure is pursued.
b. Procedures. The following guidance criteria has been derived from past
certification policy and experience. Demonstration of compliance to other criteria may
produce acceptable results if adequately justified by rational analysis. Model tests of
the appropriate ditching configuration may be conducted to demonstrate satisfactory
water entry and flotation and trim characteristics where satisfactory correlation between
model testing and flight testing has been established. Model tests and other data from
rotorcraft of similar configurations may be used to satisfy the ditching requirements
where appropriate.
(1) Water entry.
(i) Tests should be conducted to establish procedures and techniques to
be used for water entry. These tests should include determination of optimum pitch
attitude and forward velocity for ditching in a calm sea as well as entry procedures for
the highest sea state to be demonstrated (e.g., the recommended part of the wave on
which to land). Procedures for all-engines-operating, one-engine-inoperative, and
all-engines-inoperative conditions should be established. However, only the procedures
for the most critical condition (usually all engines inoperative) need to be verified by
water entry tests.
(ii) The ditching structural design consideration should be based on water
impact with a rotor lift of not more than two-thirds of the maximum design weight acting
through the center of gravity under the following conditions:
(A) For entry into a calm sea-
(1) The optimum pitch attitude as determined in AC 27.801(b)(1)(i) with
consideration for pitch attitude variations that would reasonably be expected to occur in
service;
(2) Forward speeds from zero up to the speed defining the knee of the
height-velocity (HV) diagram;
(3) Vertical descent velocity of 5 feet per second; and
(4) Yaw attitudes up to 15°.
(B) For entry into the maximum demonstrated sea state-
Page D - 84
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.