FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-83

PDF page 356 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 356
AC 27-1B · D-83Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (4) A sea state 4 is defined as a moderate sea with significant wave heights of
4 to 8 feet with a height-to-length ratio of:

                  (i)    1:12.5 for multiengine rotorcraft with Category A engine isolation
(reference paragraph AC 27 MG 3).

                   (ii)   1:10 for all other rotorcraft.

NOTE: The source of the sea state definition is the World Meteorological Organization
(WMO) Table. (See figure AC 27.801-1.)

         (5) Ditching certification encompasses four primary areas of concern: rotorcraft
water entry, rotorcraft flotation and trim, occupant egress, and occupant survival.

         (6) The rule requires that after ditching in reasonably probable water conditions,
the flotation time and trim of the rotorcraft will allow the occupants to leave the rotorcraft
and enter liferafts. This means that the rotorcraft should remain sufficiently upright and
in adequate trim to permit safe and orderly evacuation of all personnel.

         (7) For a rotorcraft to be certified for ditching, emergency exits must be
provided which will meet the requirements of § 27.807(d).

         (8) The safety and ditching equipment requirements are addressed in
§§ 27.1411, 27.1415, and 27.1561 and specified in the operating rules (Parts 91, 121,
127, and 135). As used in § 27.1415, the term ditching equipment would more properly
be described as occupant water survival equipment. Ditching equipment is required for
extended overwater operations (more than 50 nautical miles from the nearest shoreline
and more than 50 nautical miles from an offshore heliport structure). However, ditching
certification should be accomplished with the maximum required quantity of ditching
equipment regardless of possible operational use.

         (9) Current practices allow wide latitude in the design of cabin interiors and,
consequently, the stowage provisions for safety and ditching equipment. Rotorcraft
manufacturers may deliver aircraft with unfinished (green) interiors that are to be
completed by the purchaser or modifier. These various “configurations” present
problems for certifying the rotorcraft for ditching.

                  (i)    In the past, “segmented” certification has been permitted to
accommodate this practice. That is, the rotorcraft manufacturer shows compliance with
the flotation time, trim, and emergency exit requirements while the purchaser or modifier
shows compliance with the equipment provisions and egress requirements with the
completed interior. This procedure requires close cooperation and coordination
between the manufacturer, purchaser or modifier, and the FAA/AUTHORITY.

                   (ii)   The rotorcraft manufacturer may elect to establish a “token” interior for
ditching certification. This interior may subsequently be modified by a supplemental


                                                       Page D - 83

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →