FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-81

PDF page 354 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 354
AC 27-1B · D-81Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


         (5) Compartment lamps must be protected from possible lamp bulb and cargo
contact.

         (6) Other than the standards in this section, specific standard design features
for cargo compartment doors are not contained in FAR Part 27. The following are
recommended design features.

                  (i)   Door latch or lock mechanism should not fail and allow the door to
open and should not open as a result of cargo shifting.

                   (ii)  Crewmembers should by visual means such as handle positions and
markings determine, when on the ground, that the door is fully locked. A separate
signal system may also be used to show a door unlatched condition.

         (7) Compartment marking standards such as maximum weight, floor loading,
possible tiedown instructions and other appropriate compartment markings or placards
are prescribed in § 27.1557(a).

     b. Procedures.

         (1) The compartment design allowable load, including distributed loading, is
determined during the initial design phases of the rotorcraft. For an example, the
compartment may have a placarded maximum allowable load of 250 pounds, with an
allowable distributed load of 100 pounds per square foot. The compartment maximum
load and floor distributed load (allowable pounds per square foot) should be included in
a stencil, placard, or equivalent durable marking per § 27.1557(a).

         (2) Static tests or analyses may be used for substantiation. Light weight
rotorcraft configurations typically should be associated with the most severe flight and
landing load factors.

         (3) Structural substantiation of the fuselage for flight and landing loads must
include the baggage and cargo restraining devices and associated attachment
structure. Structural substantiation of the compartment structure must include the
4g ultimate forward load condition of § 27.787(c) in addition to the flight and landing
load conditions. These can be handled as separate conditions if the structure is
substantiated by analysis.  If static tests are conducted, all load conditions must be
accounted for. A test plan should be approved and conformity inspections conducted
prior to FAA/AUTHORITY witnessing of tests.

         (4) Cargo nets or straps installed for compliance with § 27.787(b) must be
substantiated for the maximum flight and landing loads. The forward load condition of
§ 27.787(c) must be proven also. Nets or straps should be adjustable.




                                                       Page D - 81

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →