Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
(2) Section 27.562 includes a specific pass fail criteria, which includes head
injury criteria.
(3) Shoulder harnesses need only be substantiated for 40 percent of total
occupant load rather than the former 60 percent adopted by Amendment 27-21.
(4) AC paragraph 27.562 provides guidance for evaluating the functioning of a
seating energy absorption device system under dynamic test conditions. Stroking is
generally associated with the vertical-horizontal impact case and is recognized in the
static strength substantiation.
(5) Berths or litters installed within 15° or less of the rotorcraft longitudinal axis
(oriented longitudinally) shall use a combination of restraint devices, such as a padded
end-board, cloth diaphragm, or equivalent means to withstand and distribute the
occupant loads resulting from § 27.561(b) requirements. Other berths or litters may be
equipped with straps or safety belts to withstand the forward reaction of § 27.561(b) as
well as other loads, including flight loads.
(i) Berths/litters may be substantiated by static load tests, analysis, or a
combination thereof and need not be substantiated to the 1.33 fitting factor of seat
installations.
(ii) The berth/litter occupant’s head, neck, and spine should be protected
from (landing) impact forward loads by appropriate design means; e.g.,
• non-longitudinal orientation of the berth/litter; or
• “feet forward” orientation; or
• distribution of an appropriate percentage of forward loads on the
shoulders (not solely to the head and spine).
(iii) Recommendations for litter occupant
• If the occupant’s head is oriented forward, a shoulder harness
should be provided, in conjunction with body and leg straps, that
prevents the occupant’s head from falling off the litter. A padded
end board, diaphragm, etc., may be used, provided head and spinal
loads are alleviated or prevented.
• If the occupant’s feet are oriented forward, the padded end board
may also be used in combination with body and leg straps or other
such restraints.
Page D - 79
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.