Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(5) Projecting objects which could injure occupants in normal flight should be
padded. The amount of padding required depends on the location, size, and minimum
radius of the projecting object. In general, this requirement may be met by padding
sharp edges with one-half inch of PVC foam or equivalent energy absorbing material
(5 to 10 lbs. density). Objects with edge radii in excess of 1 inch may meet the
requirements of § 29.785(e) with a lesser amount of energy absorbing padding, if it can
be contacted only by persons while “seated or moving about in the rotorcraft in normal
flight.”
AC 27.785A. § 27.785 (Amendment 27-25) SEATS, BERTHS, SAFETY BELTS,
AND HARNESSES.
a. Explanation.
(1) The title of § 27.785 now includes berths (which would include litters).
(2) Section 27.785(a) has been revised to include reference to the new
§ 27.562, “Emergency Landing Dynamic Conditions”.
(3) Section 27.785(b) has been revised to include a reference to the new
§ 27.562(c)(5) head injury criteria and to describe a torso restraint system that is
contained in TSO-C114.
(4) Section 27.785(f) has been revised to change the percentage of load
distribution of a combined safety belt and harness from 60-60 to 60-40.
(5) A new § 27.785(i) has been added which provides a list of “seating device
system” components.
(6) A new § 27.785(j) provides for deformations of the seat energy absorption
device system installed to meet the requirements of § 27.562 but requires that the
system “remain intact and not interfere with rapid evacuation of the rotorcraft.” Further
“structural” performance standards are contained in §§ 27.562(c)(1) and (2).
(7) A new § 27.785(k) provides static strength and restraint requirements for
litters and berths. Litters may be oriented laterally as well as longitudinally in the
rotorcraft. Dynamic tests of litters are not required. For longitudinally oriented litters,
features should be provided to protect the occupant from the increased loads in
§ 29.561(b) of Amdt. 27-25.
b. Procedures. The procedures of paragraph AC 27.785 still apply to static
substantiation of the seats, berths, safety belts, and harness. In addition:
(1) Compliance with § 27.562 (except litters are not included) and § 27.561(b)
is required.
Page D - 78
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.