FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-77

PDF page 350 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 350
AC 27-1B · D-77Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


                  (i)   Whenever a harness is used, it should support the shoulders without
applying hazardous loads to the side or front of the neck.  It should be easily donned
and removed. A single point release with the seat belt is required for each pilot’s seat
and preferred for other seats.  If a separate release is provided, it must be simple,
compatible with the seat belt release, and near the seat belt release. The harness
should be tested in conjunction with the seat belt using a “body block” similar to that of
NAS 809, if possible.  It shall be tested to 60 percent of the § 27.561 minor crash loads
for the entire occupant weight of 170 pounds. TSO-C114, Torso Restraint Systems,
dated May 27, 1987, was recently issued.

                   (ii)   During certification TIA testing, the pilot shall ensure that all of the
pilot’s necessary functions may be performed with the seat in the most adverse
adjustable position and the belt and harness fastened. Each belt and harness shall also
be secured, when not used, if necessary, to comply with § 27.785(c).

                    (iii)   Elimination of injurious objects within striking distance of the head and
other vital parts can be accomplished by removal of objects with sharp edges or rigid
surfaces from within striking distance of vital parts of the occupant. Dimensions and
weights for typical occupants are available in U.S. Army USAAVLABS Reports 70-22
(August 1969) and 66-39 (June 1966) and NACA Report TN 2991 (August 1953).
Because of the range of occupant head striking distance, a combination of “elimination
of injurious objects” and “cushioned rests” may be required for some interior
configurations.  If only a belt or a belt-harness which allows use of only the belt is
installed, the minimum arc or strike sphere requirement may be met by establishing a
35-inch minimum radius strike-free zone from the seat back and bottom cushion
junction. The cushions may be assumed to be normally compressed.

               (iv)  An acceptable cushioned rest can be provided by use of a 1-inch
thickness of foamed polyvinyl chloride (PVC) or equivalent energy absorbing material.
The density of material should be in a 5- to 10-pound per cubic foot density range. PVC
foam has the property of absorbing energy efficiently with negligible rebond effects.
PVC foam recovers slowly to the original configuration after deformation.  If PVC foam
is used, however, care must be taken in its application relative to its flammability
characteristics (reference § 27.853).

         (4) Handholds for the occupants are generally provided by transport aircraft
seat backs adjacent to the aisle.  If the seat backs fold, the amount of support provided
by the seat backs before they fold must be evaluated in a furnished interior or mockup.
To provide adequate support, the seat back may use an easily disengaged latch or
adequate friction in the hinge mechanism to obtain adequate support. Handholds along
the aisle are, of course, not needed for rotorcraft with no aisles or where seat belts must
be fastened during flight according to the operating rules.





                                                       Page D - 77

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →