FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-76

PDF page 349 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 349
AC 27-1B · D-76Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

                  (i)   Dynamic impact tests may be voluntarily proposed by the applicant.
At least two conditions should be used to be representative of impact cases. Report
No. DOT/FAA/CT-85/11, Analysis of Rotorcraft Crash Dynamics for Development of
Improved Crashworthiness Design Criteria, June 1985, may be obtained for reference
from the National Technical Information Service, Springfield, Virginia 22161.

                   (ii)   Advisory Circular 21-22, Injury Criteria for Human Exposure to Impact,
June 20, 1985, may be used for part of the acceptance levels or performance criteria in
developing a proper dynamic test proposal. The static design conditions contained in
the present standards shall be satisfied also.

      c. Procedures.

         (1) Each seat with its belts and harnesses are to be substantiated for the flight,
ground, and emergency landing loads of § 27.561 by structural test or stress analysis.
Approval can be gained by Technical Standard Order (TSO) approval or by
accomplishing sufficient structural substantiation to gain certification approval of the
seat and its belt(s) and harness as part of the type design of the rotorcraft.
TSO No. C-39a concerns standards for aircraft seats, including rotorcraft seats.  If TSO
No. C-39a is used as an approval basis for a specific rotorcraft seat, the seat and
harness should be checked to ensure it has been substantiated for the vertical (up and
down) and side loads imposed by installation in the aircraft. For example,
TSO No. C-39a (and NAS 809) specifies an ultimate down load of 4.0g which is in
agreement with the 4.0g emergency landing load factor of § 27.561, but it may be less
than the design maneuver load factor (which can be as high as 3.5g limit or
5.25g ultimate).

                  (i)   The 1.33 factor is specified for substantiation of attachments of each
seat to the structure and each safety belt or harness to the seat or structure and the
head rest, if used, for § 27.561 loads, whether analysis or test is used.

                   (ii)     If static testing of seats, belts, and harnesses is used, the body block
of NAS 809 may be used. The corners of the NAS 809 body block may be radiused
and padded if it is found that the small radii cause premature, unrealistic crippling of thin
wall tubing or other structure used in the static seat.

                    (iii)  The substantiation of the pilot seats is required to include pilot forces
of § 27.397 in conjunction with normal flight and ground loads. For example, the pilot
foot force (195 pounds ultimate) must be reacted by the seat.

         (2) The head rest, if used, shall be substantiated for a head weight of
13 pounds, § 27.561 inertia load factors, and a factor of 1.33 whether by test or
analysis.

         (3) The following criteria have been found satisfactory for preventing occupant
head injuries:


Page D - 76

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →