FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-75

PDF page 348 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 348
AC 27-1B · D-75Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

each occupant with every reasonable chance of escaping serious injury for the stated
conditions.

         (2) The standard includes both serious (general) injury, paragraphs (a) and (e),
and head injury, paragraph (b). Furthermore, paragraph (b) requires certain design
features or practices for head injury protection.

         (3) The pilot seats shall additionally withstand the pilot control effort forces
stated in § 27.397.

         (4) Seat or berth static test or structural analysis conditions (which are
procedures) were previously stated but removed by Amendment 27-21.

     b. Background.

         (1) FAR Part 27 through Amendment 27-20 and its predecessor, CAR Part 6,
specified design conditions (flight, landing, and emergency landing conditions, § 27.561)
for each seat and berth. Pilot seats were also subject to pilot control forces (reaction) of
§ 27.397. Structural strength analysis and testing could be simplified or conditions
combined as stated. A factor applied to each design load shall be at least the “fitting”
factor specified in § 27.625 and applied as stated therein.

         (2) Amendment 27-21, adopted November 1984, expanded the standard
significantly to contain objective and specific standards for improved occupant
protection for flight, landing, and the emergency landing conditions of § 27.561.

                  (i)   A shoulder harness is required for each front seat occupant. A
shoulder harness (also called upper torso restraint) or other means shall be used to
protect other occupants from head injury. Design features of the belt and harness are
also included. A factor of 1.33 was also adopted. Protection while seated or moving
about during normal flight and moderately rough air is also a part of the amended
standard. This is similar to the transport rotorcraft standards.

                   (ii)  A load distribution between the belt (60 percent) and harness
(60 percent) is stated. Design standards for any head rest, if installed, are stated. A
factor of 1.33 shall be applied to the design loads for the attachment of each seat to the
structure and each belt and/or harness to the seat or structure and the head rest. This
factor is applied whether the seat and restraint system is proven by static test or by
analysis.

         (3) An AC applicable to safety belts and shoulder harnesses for small airplanes
has been issued. The information in AC 23-4, “Static Strength Substantiation of
Attachment Points for Occupant Restraint System Installations June 20, 1986, should
be helpful in complying with § 27.785.




                                                       Page D - 75

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →