Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(ii) If necessary, a door and engine or rotor system interlock system may
be employed to prevent opening of the door with the rotors operating. Other systems
may be used. In case of emergency, the system must allow opening of the door (exit)
from inside or outside the rotorcraft.
AC 27.783A. § 27.783 (Amendment 27-26) DOORS.
a. Explanation.
(1) Each closed cabin should have at least one door. A door on the opposite
side of the cabin may be used to also comply with the exit requirement of § 27.807.
(2) Amendment 27-26 extends the requirements of § 27.783 to:
- include each external door, not just passenger doors; and,
- require provisions of door location and procedures to protect persons from
danger from propellers, engine intakes, and engine exhausts.
b. Procedures. All of the policy material pertaining to this section remains in
effect. In addition:
(1) Occupants of the rotorcraft and servicing personnel should be protected
from possible injury when using any external door to enter or egress the rotorcraft and
when loading cargo or servicing the rotorcraft. Consideration should be given to door
location and operating procedures to include protection from propellers (if equipped)
and engine inlets and exhausts, as well as from rotors.
(2) These new requirements clarify that engine exhausts, engine inlets, and
propellers, as well as rotors, are potentially hazardous and should be located or
designed to protect rotorcraft occupants and ground personnel.
(3) Door operating procedures, including readily visible markings, should be
provided to minimize possible injury to personnel when practical component locations or
component design features, alone, do not assure freedom from possible injury.
AC 27.785. § 27.785 (Amendment 27-21) SEATS, BERTHS, SAFETY BELTS, AND
HARNESSES.
a. Explanation.
(1) The standard concerns occupant seat and berth (litter) devices and restraint
of the occupant (170-pound weight) for specified conditions. The occupants shall be
restrained and protected for flight, landing, and the emergency landing conditions
specified in § 27.561(b). This standard and § 27.561 have the objective of providing
Page D - 74
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.