FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-70

PDF page 341 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 341
AC 27-1B · D-70Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

controls, and landing gear controls, it applies to all cockpit controls not addressed in
other paragraphs.

     b. Procedures.

         (1) The cyclic should be mechanized such that movement of the control results
in a corresponding sense of aircraft motion in the same axis. While a certain amount of
coupling may be present following a pure control input in a given axis, that coupling
should not be objectionable to the pilot. Collective pitch control should be mechanized
such that an upward movement of the collective results in a corresponding relative
motion of the aircraft in the vertical plane. Again, coupling should not be objectionable.
Care should be taken to insure that the primary pilot’s perception of collective motion is
in the vertical plane. The objective is to clearly differentiate collective motion from that
associated with an airplane throttle. The rule is self-explanatory on the subject of
engine power controls. A distinction is made between normal landing gear controls and
emergency controls. Emergency controls may operate in a sense which might not
correspond to the direction of resultant gear motion.

         (2) The recommended operating convention and “switchology” for
miscellaneous controls are:

                  (i)   Up/forward = on/increase

                   (ii)   Down/aft = off/decrease

                    (iii)   Variable rotary controls should move clockwise from the OFF position,
through an increasing range, to the full ON position. For some variable intensity
controls such as instrument lighting, the desired minimum setting may not be completely
off. Pushbuttons not giving an obvious indication of mechanical position should be
configured such that the flightcrew has a clear indication of switch actuation under both
day and night (if applicable) conditions. Failure of the indication should be shown to be
free of hazards.

         (3) Slew or “beep” switches associated with flight control system applications
warrant special attention. The recommended conventions for control-mounted single, or
multifunction, two or four-way “beep” switches are:





Page D - 70

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →