Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
06/28/18 AC 27-1B, Chg 8
This requirement is in addition to any area of visibility specified by paragraph AC
27.773.(b)(2)(i) which may be included in the overhead window area.
(C) If the instrument panel obstructs any required area between 10° left
and 10° right below 20° forward and below the horizon, a window which affords triple
equivalent additional visibility should be located immediately below and between the
angles of 20° left and 20° right above 65° below the horizon.
(v) For steep rejected takeoffs and steep approaches (such as to oil rigs or
confined heliports), the visibility should be such that the pilot can see the touchdown
pad and sufficient additional area to the side and forward to provide both an accurate
approach to the touchdown point as well as a satisfactory degree of depth perception. A
5-inch head movement by the pilot forward and/or sideward of the normal position is
acceptable in determining compliance.
(2) Since glare and reflection often differ with the sun’s inclination, consideration
should be given to evaluating the cockpit at midday and in early morning or late
afternoon. Windshields with embedded wire heating elements should be evaluated for
distortion with the system both “ON” and “OFF.” Assess glare from reflected light to
ensure that it does not reflect into the pilots’ eyes. Assess reflections of pilot or cockpit
structures off of instrument glass that may interfere with the readability of displays or
instruments. This problem is most apparent in IFR equipped aircraft (having larger
instrument panels and avionic consoles) operating in VFR utility roles.
If night approval is requested, then compliance with 27.773 may be shown by either a
ground or flight test. Internal lighting can be evaluated with a ground test. External
lighting modifications may require a flight test. If a flight test is conducted, then the
lighting system should be evaluated in likely combinations and under expected flight
conditions.
(i) Internal lighting evaluations may be accomplished by a ground test with
the aircraft in a dark hangar or with external light blocked to create a dark cockpit.
Locations and intensity of instrument panel and control panel light reflections should be
assessed to ensure they do not interfere with the pilots’ ability to see outside the
aircraft. Figure AC27.773-1 contains guidance on the areas in pilots’ field of vision
where reflections should be eliminated. Although a certain amount of equipment
reflection (avionics control heads, etc.) in the windshield may be unavoidable, the pilot’s
normal field of view should be unobstructed. If reflections are mitigated by modifying the
glare shield, then the pilots’ field of view should be revaluated. If a reflection’s effect on
the pilots’ ability to see outside the aircraft is uncertain, a night flight test may be
required.
(ii) External lighting evaluations should be done during night flight tests.
Evaluating external lights on the ground may result in unacceptable light entering the
cockpit and causing reflections or glare due to reflection off the ground or surrounding
structures. Landing and taxi lights should be exercised throughout their adjustment
range (if applicable) to check for reflections, particularly in chin windows. Anticollision
and strobe lights should be evaluated to ensure that frequency interaction and
reflections
D - 65
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.