Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
06/28/18 AC 27-1B, Chg 8
(ii) A dual lens camera, as photo recorder, should be used in measuring the
angles specified in the paragraphs listed below. Other methods, including the use of a
goniometer, are acceptable if they produce equivalent areas to those obtained with a
dual lens camera. When not using a dual lens camera, compensation should be made
for one half of the distance which exists between the eyes, or 1 ¼ inches. With the
referenced eye position located as indicated in paragraph AC 27.773b.(1)(i), and
utilizing binocular vision and azimuthal movement of the head and eyes about a radius,
the center of which is 3 and 5/16 inches behind the referenced position (this point to be
known as the central axis), the pilot should have the following minimum areas of vision
measured from the appropriate eye position. (See figure AC 27.773-1.)
(A) 20° forward and above the horizon between 0° and 100° left.
(B) 20° forward and below the horizon between 10° and 100° left.
(C) 20° forward and below the horizon at 10° left increasing to a point
30° forward and below the horizon at 10° right.
(D) 50° forward and below the horizon between 10° right and 135°
right.
(E) 20° forward and above the horizon at 0° increasing to a point 40°
above the horizon at 80° right and 100° right and then decreasing to a point 20° forward
and above the horizon at 135° right.
(iii) Any vertical obstruction which falls within the minimum area of visibility
outlined in paragraph AC 27.773b.(1)(ii) should be governed by the following:
(A) Between 20° right and 20° left--no vertical obstruction.
(B) Between 20° right and 135° right -- no vertical obstruction greater
than 2.5 inches in width.
(C) Between 20° left and 100° left -- no vertical obstruction greater than
2.5 inches in width.
(iv) Any horizontal obstruction which falls within the minimum area of
visibility outlined in paragraph AC 27.773b.(1)(ii) should be governed by the following:
(A) The area 15° forward and above the horizon between 135° right
and 40° left decreasing to a point 10° above the horizon at 100° left, and 15° forward
and below the horizon between 135° right and 100° left should be free from horizontal
obstructions.
(B) The area above and below the horizon which is between the
minimum area of vision specified in paragraphs AC 27.773b.(1)(ii) and AC
27.773b.(1)(iv)(A) is limited to one horizontal obstruction above and one below the
horizon. These horizontal obstructions should not be greater than 4 inches in width. An
overhead window which will provide twice as much additional visibility as that lost due to
the obstruction should be located immediately above any obstruction above the horizon.
D - 64
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.