FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 334

PDF page 334 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 334
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

06/28/18                                        AC 27-1B, Chg 8


AC 27.773. § 27.773 (Amendment 27-48) PILOT COMPARTMENT VIEW.

    a. Explanation. The section outlines requirements for pilot view in fairly general
terms. Requirements are purposely less stringent than for transport category rotorcraft
to allow for cockpit designs ranging from fully enclosed to open to the elements. Section
27.773(b) was changed at amendment 27-48 to include the option for a ground test in
lieu of a night flight test. Paragraph b.(2) below contains guidance to reflect this change.

    b. Procedures.

       (1) The following procedures are one acceptable means of evaluating pilot
compartment field of view considering only those objects in the pilot compartment and
the windshield and its support structure in nonprecipitating conditions. The applicant’s
design is not required to meet these guidelines, and each design should be evaluated
on its own merit. The area of visibility established in the following paragraphs will
provide an acceptable level of visibility for a minimum crew of one pilot. In the event that
a minimum crew of two, a pilot and copilot, is required, the second pilot should have an
area of visibility equivalent to that provided for the pilot but on the opposite side. In this
event, the pilot’s area of visibility to the left as shown in figure AC 27.773-1 needs only
to comply to 60° left, and the copilot’s area of visibility to the right needs only to comply
to 60° right.

                 (i)  A single point established in accordance with the provisions of this
paragraph constitutes the referenced eye position (i.e., a point midway between the two
eyes) from which the central axis may be located. The referenced eye position is a
reference datum point from which the aircrew station geometry is constructed. The
referenced eye position should be located by means of ship’s coordinates that contain
station reference number, water line, and butt line for both pilot and copilot, if applicable,
and comply with:

               (A)  The pilot’s seat in a normal operating position from which all
controls can be utilized to their full travel by an average subject, and which should
provide for vertical adjustment of the seat of not less than 2.5 inches above and 2.5
inches below this initial vertical position.

               (B)  The seat back in its most upright position.

               (C) The seat cushion depression being that caused by a subject
weighing 170 to 200 pounds.

               (D) The longitudinal axis of the rotorcraft to be that of “cruise attitude”
(0.9VH or 0.9VNE whichever is lower).

               (E)  The point established not beyond 1 inch to the right or left of the
longitudinal centerline of the pilot’s seat.

                (F)   All measurements made from the single point established in
accordance with this paragraph.



                         D - 63

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →