FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-62

PDF page 333 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 333
AC 27-1B · D-62Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

             SUBPART D - DESIGN AND CONSTRUCTION

            PERSONNEL AND CARGO ACCOMMODATIONS


AC 27.771.  § 27.771 PILOT COMPARTMENT.

     a. Explanation.

         (1) Volumes have been written on human factors and their contribution to pilot
workload and fatigue. This document cannot begin to address the myriad of
considerations involved in pilot compartment design. The intent of the rule is simply to
ensure that reasonable human factor engineering practices have been followed.
Equipment should be logically grouped within the pilot’s reach and view and be easy to
operate. Seats should provide a reasonable level of comfort for the normal
anthropometric range of pilots for a typical mission duration. Environmental
considerations such as radiation from the sun through overhead windows should be
addressed. Heating, cooling, and ventilation systems should be adequate for the
expected range of operating conditions.

         (2) Each pilot compartment and its equipment should allow the minimum
flightcrew to perform their duties without unreasonable concentration or fatigue.  If there
is a provision/requirement for a second pilot, his station should be equipped with
primary flight controls. Duplicate wheel brakes are recommended. Duplication of
miscellaneous controls such as idle detent switches, RPM beep functions, nosewheel
locks, and parking brakes has not been required. The need for duplicate instruments
for the second pilot tends to be a function of cockpit size and panel configuration.

         (3) Webster defines appurtenances as “accessory objects or apparatus.” Items
such as blowers, fans, and gyros should not have noise or vibration characteristics
which could contribute to pilot fatigue or distraction. Instrument panel vibration is
specifically addressed in § 27.1321.

     b. Procedures.  Initial evaluation of the pilot compartment should be conducted on
the ground. However, the cockpit assessment should be an ongoing effort throughout
the flight test program.  If a second pilot position is provided/required, the adequacy of
controls and instruments should be evaluated under all normally expected operating
conditions.  If a second pilot position is not provided/required, any passenger position in
the pilot compartment should be evaluated to ensure that a passenger, properly briefed
by the flightcrew, can sit comfortably without inadvertent interference with normal
control operations. All equipment should be operated during at least one flight of typical
mission profile and duration.





Page D - 62

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →