FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-60

PDF page 331 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 331
AC 27-1B · D-60Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

AC 27.753  § 27.753 MAIN FLOAT DESIGN.

     a. Explanation. Loads and load distributions are specified for float design as
follows:

         (1) Bag floats are to be designed for:

                  (i)   The maximum pressure differential developed at the maximum design
altitude.

                   (ii)   The vertical loads prescribed in § 27.521(a) distributed over
three-fourths of the bag’s projected area.

         (2) Rigid floats are to be designed for vertical, horizontal, and side loads
prescribed in § 27.521 distributed along the length of the float.

     b. Procedures. Structural substantiation may be accomplished by static tests or
analyses using the specified loads. Substantiation should cover the float and float
attachments.

AC 27.755  § 27.755 HULLS.

     a. Explanation.

         (1) The section requires amphibious rotorcraft with a single hull (main float
design) and with auxiliary floats (outriggers) to provide a margin of positive stability
great enough to minimize the probability of capsizing when any single (usually the most
critical) compartment is flooded. Landing gear wheel tires may be used for stability
purposes as well.

         (2) Limitations for water operation are not intended by this section, but
information for water operation must be included in the rotorcraft flight manual.

         (3) Wave height or sea state and buoyancy relative to fresh water is not
specified but is encompassed in the objective statement of § 27.751(b).

         (4) Section 27.751 specifies an excess buoyancy requirement of 50 percent for
single main floats (hulls) and contains a capsize/stability standard also. This section
complements § 27.755 for certain hull designs.

         (5) Sections 23.751, 23.755, and 23.757 concern design standards for small
airplanes and may provide insight into possible rotorcraft hull designs.

     b. Procedures.




Page D - 60

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →