Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
SUBPART D - DESIGN AND CONSTRUCTION
FLOATS AND HULLS.
AC 27.751 § 27.751 (Amendment 27-2) MAIN FLOAT BUOYANCY.
a. Explanation.
(1) The section specifies standards for single and multiple float buoyancy in
fresh water. The standard does not apply to ditching/emergency flotation devices, but
to amphibian rotorcraft devices.
(2) It is a design and a performance standard. Rigid or inflatable floats may be
used. Enough water tight compartments (per Amendment 27-2) rather than a specific
number are required to minimize the probability of capsizing when one compartment is
flooded or deflated.
b. Procedures.
(1) Excess buoyancy. A minimum of 50 or 60 percent in excess of the
maximum certificated weight of the rotorcraft is required for single or multiple floats
respectively. The weight of fresh water (density 62.42 pounds per cu. ft.) displaced by
fully submerged float or floats (total volume at operating pressure of each float is used)
should be a minimum of 50 or 60 percent greater than the maximum certificated weight
of the rotorcraft.
(2) Capsizing.
(i) Each float should have enough sealed, separate and approximately
equal volume compartments to minimize the probability of capsizing when the critical
compartment is flooded or deflated. Five or more compartments in each float are
usually necessary to meet the standard. Ten compartments per float have been
employed in certain designs.
(ii) An analysis or test or combination thereof may be used, if necessary,
to prove a positive margin of stability with the most “critical” compartment in one float
flooded or deflated, that is ineffective.
(iii) The location of the floats, and the most critical compartment, the
rotorcraft weight, mass moment of inertia, and center of gravity location are also
important considerations for capsize stability.
Page D - 59
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.