FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-58

PDF page 329 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 329
AC 27-1B · D-58Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


         (6) During an inspection of the landing gear, such as an engineering
compliance inspection, the brake location should be checked to ensure the brake does
not contact the ground when the tire is deflated. Type design drawings should control
the proper location of the brake on the landing gear.

AC 27.737.  § 27.737 SKIS.

     a. Explanation. This standard is derived from airplane standards. Aircraft skis
approved under TSO-C28 may be used on rotorcraft. TSO-C28 for aircraft skis refers to
Sections 4 and 5 of National Aircraft Standards Specification 808, dated
December 15, 1951, for strength and performance standards. These standards are
conservative for rotorcraft ski installations.

         (1) A maximum limit load rating is assigned to each ski approved under
TSO-C28.

         (2) This limit load rating must not be exceeded by the maximum limit ground
load determined under the standards of § 27.505, Ski landing conditions.

         (3) Ski mounting or installation parts used in the particular application are
subject to substantiation as any landing gear member is subject to substantiation.

         (4) Ski installations are also subject to flight and ground operation evaluations.

     b. Procedures.

         (1) The limit load rating for the ski selected shall be obtained from the ski
manufacturer. This information shall be included in the design criteria and/or structural
substantiation reports. The type design drawings will include the appropriate part
number for the TSO-approved product and the necessary installation information.

         (2) The design limit loads derived in compliance with § 27.505 shall not exceed
the ski limit load rating.

         (3) Skis that are not TSO approved may be approved as a part of the aircraft
type design by complying with the strength and performance standards contained in
TSO-C28 (NAS 808).

         (4) Pads or “bear paws” installed on skid or wheel landing gear to facilitate
operations in snow conditions may be approved as a part of or as an alteration to the
aircraft type design. Rational design loads applicable to the particular pad design must
be developed and strength substantiating data submitted proving compliance with the
strength and performance standards contained in Part 27. In addition, skid landing gear
may be subject to excessive vibratory loads while in flight whenever the weight and
mass distribution is altered by adding “bear paws.” The effect of additional weight
should be investigated. Resonant vibratory conditions should be avoided or highly
damped.

Page D - 58

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →