Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(5) Although not specifically noted in a standard, the position of the brake on
the wheel is important. The brake should be positioned to avoid ground contact
whenever the tire is deflated.
(6) TSO-C26 contains minimum performance standards for aircraft landing
wheels and wheel-brake assemblies. For rotorcraft, a wheel-brake assembly design
rating is established by the manufacturer. The TSO standard for rotorcraft brakes
specifies a 20° slope standard (rather than a 10° slope) for an over-pressure hydraulic
brake test.
(7) The brake application device at the pilot station is subject to other structure
strength standards in this Part, such as the limit pilot forces or torque specified in
§ 27.397.
b. Procedures.
(1) Wheel-brake assemblies approved under TSO-C26 will have various
(rotorcraft) ratings as specified in the standard. One rating of TSO standard for a
rotorcraft wheel-brake assembly is the kinetic energy capacity in foot-pounds at the
design landing rate of absorption. The design takeoff and landing weight and rotorcraft
speed in knots for brake application are a part of the equation. The brake manufacturer
should furnish this rating and the two noted parameters for the selected design or
designs. The ratings of selected brakes should be included in a structural design data
report such as a design criteria report. The use or application of each brake design on
the particular rotorcraft design should not exceed capacity of the brake or the ratings
established under TSO-C26. If appropriate, the part number and manufacturer of each
brake may be listed in the structural data reports as well as listed in the type design
drawings.
(2) The limiting brake torque obtained from the brake manufacturer should be
used in complying with § 27.493(b)(2).
(3) Compliance with the brake standards should be confirmed, demonstrated,
and recorded as a part of the flight test type inspection report. This applies to TSO-C26
brakes and to brakes approved as a part of the aircraft type design.
(4) If found necessary under the provisions of § 27.771, the second pilot station
should have brake control devices. The brake control devices should be listed with the
other required equipment that defines the equipment necessary for a second pilot
station.
(5) A brake assembly may be evaluated and approved under Part 27 as a part
of the aircraft type design. TSO-approved brakes are not specifically required but are
recommended. For non-TSO-approved brakes, all detail and assembly drawings,
required test proposals, and test results reports may be submitted and processed as a
unique part of the particular aircraft type design.
Page D - 57
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.