FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-55

PDF page 326 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 326
AC 27-1B · D-55Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


         (4) The Tire and Rim Association, Inc., generally issues a yearbook listing tire
and rim sizes and ratings. The dimensions and contours for aircraft wheel rims are
contained in Section 9 of this yearbook.

AC 27.733.  § 27.733 (Amendment 27-11) TIRES.

     a. Explanation.

         (1) This standard specifies both design and performance criteria for tires. The
tire must fit the wheel rim. The maximum static ground reaction for the condition
specified must not exceed the maximum static load rating of each tire. In addition, any
tire of retractable gear systems must have adequate clearance from surrounding
structure and systems as specified.

         (2) Main, nose, and tail wheel tires must comply.

         (3) Tire performance standards are contained in TSO-C62.

     b. Procedures.

         (1) The aircraft structural design loads should contain a maximum static load
imposed on the tires. The load is derived for a static ground reaction assuming the
design (maximum) weight and the critical center of gravity for each tire of the landing
gear. The wheel loads are determined under § 27.731(b). Reduced weight but forward
CG conditions may result in the highest static load on a nose wheel tire. Thus,
combinations of weight and CG locations require investigation for the maximum tire load
of each main, nose, and tail wheel tire.

         (2) The maximum possible size of the tires considering appropriate
temperatures, aging, and pressure should be obtained to check wheel well and cover
clearances. Tire dimensions (for clearances) may be found in the yearbook noted in
paragraph AC 27.733b(4).  If the tire clearance is questionable, objects may be taped to
the tire to simulate tire growth or oversize dimensions expected and the wheel retracted
and rotated by hand to check for possible interferences. Minimum clearance, such as
one-half inch, may be adequate as a design objective. The design drawings should be
reviewed for information of correct systems installations and landing gear rigging within
the wheel wells and wheel covers, if installed.  If necessary to control tire sizes, specific
manufacturer’s tires should be used as “required equipment” and the tire manufacturer
and the part number should be specified in the design data and on the type certificate
data sheet as “required equipment.”

         (3) As specified in paragraph d of § 27.729 adopted by Amendment 27-21, an
operation test of any retractable landing gear should be performed. During this
operation test, the tire clearances described in paragraph AC 27.733b(2) should be



                                                       Page D - 55

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →