FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-54

PDF page 325 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 325
AC 27-1B · D-54Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

distinctive in its operation from other warning devices incorporated into the rotorcraft
cockpit design.

                    (iii)  An acceptable method of interlocking a normal landing mode and the
position of the landing gear would be through the selection of some appropriate speed
that is less than VLE. The system would be instrumented such that if the gear is not
down and locked and the rotorcraft goes below the selected airspeed, the landing gear
warning device would be activated.

               (iv)  An acceptable manual shut off capability would be one that allows
disabling the warning device and yet will automatically reset itself when the landing gear
is cycled or retracted, or the rotorcraft’s speed is increased above that speed selected
to activate the warning device.

              (v)  The appropriate provisions of § 27.1309 should be used to evaluate
the impact of system malfunctions.

AC 27.731.  § 27.731 WHEELS.

     a. Explanation. This standard requires use of approved wheels, either approved
under TSO-C26 or approved under the type certificate for the aircraft. Wheels must
satisfy both a design static (1g) load and design limit landing or taxiing load determined
under the applicable ground load requirements. Standards for a tire installed on a
wheel are contained in § 27.733.

     b. Procedures.

         (1) The structural design loads data shall contain both a static load and a
landing and taxiing load for each wheel. These loads are determined by virtue of
compliance with the standards of § 27.731(b) and (c). The ratings of the wheel shall not
be exceeded. TSO-C26c contains minimum performance standards for TSO approval
of aircraft wheels and wheel-brake assemblies. Ratings are assigned in accordance
with this performance standard.

         (2) If a wheel selected for an aircraft design has TSO-C26 approval, the wheel
manufacturer will supply the rating to the aircraft manufacturer. Each wheel shall be
marked as prescribed which includes a listing of the TSO number. Even though a
wheel is TSO approved, the application on the aircraft (loads imposed on the wheel)
requires proof that the rating is not exceeded.

         (3) If a wheel selected for an aircraft design is not approved under TSO-C26,
the necessary data, both detail design and assembly drawings and qualification tests
and test report data, will be required to comply with the standards contained in Part 27.
Design control and inspections will be accomplished as a part of the aircraft type
design. Structural substantiation and any appropriate qualification tests shall be
accomplished. See §§ 27.471 through 27.497 for the ground load conditions.


Page D - 54

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →