FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-53

PDF page 324 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 324
AC 27-1B · D-53Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (3) The required “downlock” should be checked during the operation test. The
design drawing should be reviewed for compliance prior to conducting an operation test.

         (4) If an optional “uplock” is installed, the landing gear should be extended
during the operation test after simulation of the critical failure mode of the retraction
system.

         (5) An “operation” test plan or proposal submitted for compliance with § 27.729
should include the items noted in 301b(3) and (4) above and should include a functional
check of the position indicator system. Those ground tests must be satisfactorily
completed before issuing the TIA.

         (6) During the official FAA/AUTHORITY flight tests, compliance with the
emergency operation, position indicator, and control aspect of § 27.729(c), (e), (f), and
(g), respectively, will be verified or accomplished. In addition, the F&R test program
plan (§ 21.35) will specify certain tests or evaluations for the retraction system.

         (7) Position Indicator Evaluation.

                  (i)   When evaluating the position indicator system, emphasis should be
placed on the switches and their installations and on the cockpit presentation. Each
gear must have its own set of switches to indicate when it is secured in its extreme “up”
position and its extreme “down” position. The switches must be located to give a valid
indication of the arrival of the gear at its extreme position.

                   (ii)   The reliability and environmental qualifications of the switches to be
used should be carefully considered. An example of a condition that has potential for
trouble is operation on wet areas. Trouble starts when water is picked up by the tires
and deposited on the switches. During winter months, the water can freeze, and the
resulting ice may prevent the switch from functioning properly.

                    (iii)  An acceptable cockpit presentation consists of two lights for each
gear. One light is colored “green” and indicates when its gear is secured in the extreme
“down” position. The other light is colored “amber” and indicates when its gear is in
transit. When the gear is in either extreme position, the in transit light is “out.” For this
presentation the indication to the pilot that the gear is in the extreme “up” position is an
all-gear lights-out condition.

         (8) Warning System.

                  (i)   A warning system to alert the crew if the landing gear has not been
fully extended and locked is required.

                   (ii)   The landing gear warning system that is provided should be evaluated
by a flight test pilot. A primary concern should be that the warning device provided is



                                                       Page D - 53

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →