FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-52

PDF page 323 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 323
AC 27-1B · D-52Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

flight condition loads. Design maximum airspeed for extension and retraction and for
fully extended conditions are required conditions.

         (3) An emergency means to extend the gear after failure of the
retraction/extension system is required for all except solely manual mechanical
systems.

         (4) This regulation requires an indication to the pilot when the gear is secured
in the extreme positions. This rule does not apply to rotorcraft that have fixed gear but
does apply to amphibious rotorcraft with retractable gear.

         (5) A “landing gear down” lock is required. An optional uplock may be used if it
meets reliability requirements.

         (6) A (ground) operation test should be conducted to ensure proper functioning
of the system.

         (7) Location and operation of the control lever or device must comply with
§ 27.777. This section includes identification of controls to prevent confusion and
inadvertent operation. Amendment 27-21 added new § 27.779 for motion and effect of
cockpit controls. Specifically, § 27.779(c) pertains to motion and effect of normal
landing gear controls. Section 25.781 of Part 25 contains large airplane design
requirements for motion, effect, and shape of cockpit controls and their knobs and
should be consulted for further guidance.

         (8) A landing gear warning is required as prescribed in § 27.729(g). Certain
features are required. The landing gear shall be extended and locked.

     b. Procedures.

         (1) The design load factors and resulting loads should be derived from the
design data. The landing gear, while retracted, operating, and extended, and its
supporting structure should be substantiated for the critical aerodynamic and inertia
loads. Yawed conditions should be considered. The specific conditions are noted in
§ 27.729(a)(1), (a)(2), and (a)(3).

         (2) Wheel well doors, if installed, should be designed for the aerodynamic
loads, including loads from yawing conditions (angles selected by the applicant) for
airspeeds up to the design maximum landing gear extended speed. Aerodynamic
effects on both open and closed doors must be considered in the door and door support
substantiations. The applicant may choose to substantiate the rotorcraft for a “landing
gear operating” and “extended” speed VLO and VLE, respectively, that is equal to the
rotorcraft VNE. This option will alleviate an airspeed “structural limitation” because of the
landing gear design substantiation. Any airspeed “structural limitation” should be listed
in the structural limitations part of the TIA.



Page D - 52

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →