Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
AC 27.727A. § 27.727 (Amendment 27-26) RESERVE ENERGY ABSORPTION
DROP TEST.
a. Explanation. Amendment 27-26 defines the word “collapse” as used in
§ 27.727(c). Collapse of the landing gear during reserve energy absorption drop tests
occurs when:
(1) A member of the landing gear will not support the rotorcraft in the proper
attitude; or,
(2) A landing gear member deforms sufficiently to allow the rotorcraft structure
other than the landing gear and external accessories to impact the landing surface.
b. Procedures. The procedures of paragraph AC 27.727A continue to apply with
the following supplemental guidance.
(1) The proper attitude for the rotorcraft after the reserve energy absorption
drop test is an attitude which allows for permanent deformation of landing gear
elements but provides for adequate egress from the rotorcraft. Refer to
paragraph AC 27.807 for emergency exit standards that relate to attitudes after a crash,
§ 27.807(b)(2).
(2) External accessories that may not impact the level landing surface during
drop testing (or equivalent gear deflections) include devices such as externally mounted
fuel tanks or accessories likely to cause post-landing fires. Expendable accessories,
such as cameras, loudspeakers, and search lights, may be damaged during landing
gear deformations resulting from reserve energy drop tests if electrical connections are
sufficiently protected to preclude electrical fires and the devices are not likely to
penetrate a fuel compartment or occupied areas. The expendable accessories, if
installed, should also be designed to not have “hard points” that would unacceptably
damage the rotorcraft structure under landing impacts by penetration into the occupied
areas or fuel tanks. Design features may be employed to preclude this penetration if
possibly hazardous. The expendable accessories, if installed, should be designed with
frangible fittings, frangible devices, or comparable design features. Also, these devices
should be designed to not significantly alter the energy absorbing ability or design
features of the landing gear.
AC 27.729. § 27.729 (Amendment 27-21) RETRACTING MECHANISM.
a. Explanation.
(1) This standard was added by Amendment 27-21.
(2) Structural substantiation is required for the gear, retracting mechanism,
doors, gear supporting structure for landing loads, maneuvering, gusts, and yawing
Page D - 51
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.