FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-50

PDF page 321 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 321
AC 27-1B · D-50Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (4) Skid landing gear is tested in attitudes prescribed in paragraph
AC 27.723a(3). Due to the construction of skid landing gear, the complete skid landing
gear is tested as a unit. Thus, the level landing with drag condition is probably the
critical attitude for the forward cross-tube and its attachments. The level landing
condition is probably the critical attitude for the aft cross-tube and its attachments.

         (5) An FAA/AUTHORITY or FAA/AUTHORITY designated or delegated person
need only witness the drop tests for “record” or “compliance.” Preliminary or
developmental drops do not require an FAA/AUTHORITY witness.

AC 27.725.  § 27.725 LIMIT DROP TEST.

     a. Explanation. Limit drop tests in the critical aircraft attitude or critical attitude of
each gear are required for the landing gear. The drop height must be at least 8 inches,
which equates to a 393-foot-per-minute (free fall) vertical descent speed. Rotor lift may
be simulated, and an effective mass may be used in the drop test as prescribed.

     b. Procedures. See paragraph AC 27.723, § 27.723.

AC 27.727.  § 27.727 RESERVE ENERGY ABSORPTION DROP TEST.

     a. Explanation.

         (1) In addition to the limit drop tests, a reserve energy drop test is required.
The landing gear must not collapse in this test to the extent that the fuselage impacts
the ground. Fracture (to separation) of landing gear parts is considered collapse of the
landing gear. This test is not an ultimate load drop test for the landing gear, except as
specified in § 27.501(a)(3) for certain skid landing gear designs using elastic spring
members.

         (2) All other types of landing gear must be substantiated for design ultimate
loads in addition to this reserve energy drop test.

         (3) Shock absorbing devices, such as oleos, must not “bottom” during the
reserve energy drop test. “Bottoming” occurs when displacement of the device no
longer occurs with increasing load.

         (4) Requirements for proof of the landing gear and airframe structure are found
in §§ 27.305, 27.307, and 27.473.

     b. Procedures. See paragraph AC 27.723, § 27.723.





Page D - 50

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →