FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-49

PDF page 320 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 320
AC 27-1B · D-49Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

so that no local failures of the aircraft occur as a result of the limit or reserve energy
drop tests.

                    (iii)   Test data. Computations for the required drop height (h) and the
effective drop weight (We) should be shown for each design level landing and tail down
landing condition in compliance with §§ 27.479 and 27.481. The computations should
be in accordance with § 27.725(a) for h and § 27.725(b) for We for the limit drop tests.
We and h are computed in accordance with § 27.725 for the limit drop test and with
§ 27.727 for reserve energy drop test. The computation of the static weight on the gear
being dropped (WM, WN, or WT) and used in the computation of We should be shown.
This static weight is defined as WM, WT, or WN for the main gears, tail gear, or nose
gear, respectively, in § 27.725(d).  It should be shown that the critical CG and proposed
certificated maximum landing weight have been used in the computation of WM, WT, or
WN. The computation of the slope of the platforms required for the inclined reaction
conditions should be presented also.

               (iv)  Test results. The results of the test are based on the values of We, h,
d, W, and L used and obtained for each drop test and the value of Nj obtained from the
accelerometer. These results should be summarized, and the method of computing the
aircraft limit inertia load factor should be shown for each drop in accordance with
§ 27.725(d). A print or copy of the film or other recording trace from the accelerometer,
if not a direct readout type of accelerometer, should be included in the test results.
Each critical condition should have several preliminary drops, as many times as
required, to obtain reasonable correlation.

         (2) Skid landing gear may be tested using similar procedures except a level
landing attitude drop test is all that is required by § 27.501. The design load conditions
specified in § 27.501(c) through (f) are derived from this level drop test condition.

                  (i)    Section 27.501(a)(2) and (3), contain special considerations for skid
landing gear.

                   (ii)   Section 27.501(a)(2) specifies that structural yielding of elastic spring
members under limit load is acceptable. This yielding or deformation is a means of
absorbing the landing impact. For skid landing gear that uses oleo or other types of
shock absorbers, the standard does not allow structural yielding under limit load.
During the limit load and reserve energy (ultimate for skid landing gear with elastic
spring numbers) drops, the yielding energy absorbing members will probably deform or
yield. After a limit drop test, the gear may be used for a reserve energy drop at the
discretion of the applicant, but a gear that has been subjected to a reserve energy drop
should not be used unless it can be shown that no yielding has occurred in that gear.

         (3) Wheel landing gear is tested in attitudes prescribed in
paragraph AC 27.723a(3). Each unit, nose or main gear, is generally tested separately.




                                                       Page D - 49

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →