Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(1) The following headings would be a typical table of contents for the test
proposal, and a generalized explanation of the contents that may be included under
each of these headings for a wheel landing gear follows.
(i) Purpose. The regulations to which compliance is being shown by the
drop tests should be identified (usually §§ 27.723, 27.725, and 27.727). Also, the
rotorcraft landing gear, including the wheels and tires to be dropped, should be
positively identified in the report by the manufacturer’s or applicant’s previously
FAA/AUTHORITY-approved drawing, technical standard orders (TSO’s), or other
identifying FAA/AUTHORITY-approved data as applicable.
(ii) Description of test setup. This section should present a description of
the test fuselage or jig, method of attaching landing gear to jig, and type of
accelerometer to be used to measure load factors. Proof of calibration of accelerometer
should be available. The accelerometer should be mounted at the aircraft CG if a free
drop of the aircraft is used or as close as practical to the centerline of the main shock
absorbing component of each landing gear (oleo, strut, etc.) if each gear is tested
separately. The description of the test jig, including platforms on which the gears are to
be dropped, should be defined by sketches in addition to the required mathematical
calculations. This data should show that the landing gear will be at the proper attitude,
relative to the platform, on impact for the particular landing condition. Drawings or other
approved data from which the geometry is taken should be referenced in the proposal.
The tire and oleo pressures at the time of the test should be specified. The method of
measuring the deflection of the tire plus the vertical travel of the axle under impact
should be described. This measurement may be accomplished by telescoping tubes
attached to the point on the jig that would measure the total (tire and oleo) vertical
deflection of the landing gear. Other vertical and horizontal deflections should be
measured as required to determine if the landing gear has experienced permanent
deformation after each drop test. The effect of surface roughness should be
considered. Smooth surfaces tend to give maximum deflections where rough surfaces
tend to restrict deflection and to result in maximum values of NZ. Preliminary company
drop tests (at less than limit drop height) may be used to determine the critical surface
roughness, or engineering evaluations may be used (without tests) when the gear
configurations are such that the critical surface condition can be analytically determined
(or when the load factor is shown to be negligibly affected by surface roughness).
NACA Report 1154, dated 1953, contains information that surface coefficients of friction
may vary from 0.4 to 0.7. Skid landing gear standards, § 27.501(c), indicate an
acceptable coefficient of friction is 0.5. A wheel landing gear design standard,
§ 27.479(b), indicates an acceptable coefficient of friction is 0.25. In the case of a small
rotorcraft, the entire aircraft may be dropped. This may be accomplished by
establishing pivot points at the main gear axles for the tail (or a point forward of the
nose gear) drops and a pivot point at the tail (or nose gear) axle for the main gear
drops. It is the responsibility of the applicant to distribute the aircraft inertia items,
including added weight to get the proper effective drop weight (We) at the landing gear,
Page D - 48
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.