FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-47

PDF page 318 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 318
AC 27-1B · D-47Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

             SUBPART D - DESIGN AND CONSTRUCTION

                         LANDING GEAR


AC 27.723.  § 27.723 SHOCK ABSORPTION TESTS.

     a. Explanation.

         (1) Limit and “reserve energy” drop tests are required as prescribed in
§§ 27.725 and 27.727, respectively. These tests may be conducted on the complete
rotorcraft or on units consisting of wheel, tire, and shock absorber in their proper
relation. For rotorcraft with skid landing gear, the tests may be conducted on the
complete rotorcraft or on a simulated fuselage with the complete skid landing gear
system.

         (2) The rotorcraft must be designed to limit load factors that equal or exceed
the limit load factor substantiated by these drop tests. In practical application, the
rotorcraft may be designed to a limit load factor, such as 2.8g. Thus, it is necessary that
the limit landing load factor derived from the landing gear drop tests be equal to or less
than 2.8g.  If not, the rotorcraft must be redesigned for the higher load factor derived
from the drop tests.  It must be shown in accordance with § 27.723 that the limit load
factors selected for design under § 27.473 will not be exceeded in landings with the limit
descent velocity corresponding to the drop height specified in that section. In addition,
reserve energy absorption capacity of the landing gear must be shown for a descent
velocity of 1.22 times the limit descent velocity selected under § 27.473 by increasing
the drop height to 1.5 times the “limit” drop height. The test requirements or procedures
outlined in Part 27 for obtaining the landing load factors are empirical; however, these
procedures are based on and supported by satisfactory experience.

         (3) As stated in § 27.725(c), each landing gear unit should be tested in the
attitude simulating the landing condition that is most critical from the standpoint of the
energy to be absorbed by it. For wheel landing gear designs, the level landing or tail
down landing and level landing with drag are generally the most critical attitude. A test
of more than one attitude may be required to comply with the standard.

         (4) Drop tests are required.  If analytical methods and/or means are proposed
by the applicant, the data presented for approval must be equal to or conservative with
respect to that data obtained from physical drop tests. Section 21.21(b)(1) concerns
“equivalency” determinations. Presenting an acceptable means of “equivalency” here
would circumvent the necessary scrutiny of an analytical method or means and is also
beyond the scope of this document.

     b. Procedures. The test plan or proposal must be approved prior to official
FAA/AUTHORITY tests unless satisfactory resolution of outstanding proposal or
conformity inspection items can be accomplished after the test.


                                                       Page D - 47

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →