Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(1) If high and low main rotor pitch stops are employed in the collective control
and if the control may be rapidly moved from one limit to the other, compliance is
shown.
(2) If detents or intermediate stops are employed, the pilot must be able to
easily and readily override, disconnect, remove, or bypass the device to allow rapid
autorotational entry prior to exceeding transient low speed rotor limits. An early
assessment of the design may be accomplished by the flight test personnel with the
evaluation completed in the Type Inspection Authorization (TIA) test program.
(3) It is acknowledged that modern rotorcraft designs may have an
autorotational VNE that is lower than “power-on” VNE or normal cruise speed. For
rotorcraft designs with this characteristic, the speed must be reduced after entry into
autorotation. No relief from the rule is required since many phases of operation occur at
speeds less than power-on VNE. For example, a critical phase of flight occurs during
takeoff. Rapid entry into autorotation is essential during this phase also.
(4) The features of the autorotational control mechanism and ability to control
the rotor speed within the design limits for any rotorcraft will be evaluated as an integral
part of the TIA test program.
AC 27.695. § 27.695 POWER BOOST AND POWER-OPERATED CONTROL
SYSTEM.
a. Reference Regulations. The following sections of Part 27 are either
incorporated in the provisions of § 27.695 or are otherwise applicable to power boost
and power-operated control systems:
(1) Section 27.307 Proof of structure.
(2) Section 27.571 Fatigue evaluation of fight structure.
(3) Section 27.671 Control system.
(4) Section 27.681 Limit load static tests.
(5) Section 27.687 Spring devices.
(6) Section 27.685 Control system details.
(7) Section 27.861 Fire protection of structure controls and other
parts.
(8) Section 27.863 Flammable fluid fire protection.
(9) Section 27.1301 Function and installation.
Page D - 44
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.