FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 308

PDF page 308 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 308
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/2008                                       AC 27-1B, Chg 3

               (2) Location of stops in close proximity to each end of a control system
will allow the stop to provide its function most efficiently without undue deflections
between the stop and its adjacent surface or its adjacent cockpit control lever or pedals.
The location of stops close to the control lever or surface will help meet the requirement
that the stop (and its function) not be appreciably affected by wear, slackness, or take-
up adjustments. Consideration should be given to limiting the total amount of take-up
adjustments of both the stop and the control systems to preclude a hazardous
adjustment of the control surface range of travel by either normal or extreme take-up
adjustment.

         (3) Each stop is to be substantiated for critical design conditions from either
pilot effort, aerodynamic loads, hydraulic loads, and other critical loads, as applicable.
The stops can be substantiated for limit loads by the tests of § 27.681.

         (4) The stops to limit the main rotor blade about its hinge points should be
positioned to prevent the blades from striking any part of the structure, particularly
during startup and shutdown operations. These stops should also limit the flapping of
the static main rotor blades of the rotorcraft when they are subjected to ground gusts
and rotor wash from nearby taxiing rotorcraft. Provisions should be made to prevent
overloading the stops or the blade under conditions of ground gusts and rotor wash
effects or during autorotational landing flares. The need for provisions to prevent
possible overloads due to ground gusts and close taxiing by adjacent rotorcraft and by
autorotational landing can be determined using the instrumented flight load survey
aircraft by hover-taxiing another rotorcraft near the instrumented aircraft and by
conducting autorotational landing flares with the instrumented aircraft. Substantiation
for the final main rotor flapping stop design can be demonstrated by similar tests.

         (5) If features of design are added to the main rotor stop assembly which
activate certain portions of the stop assembly only on the ground to meet the
requirement that the blade not hit the droop stop during any operation other than
starting and stopping the rotor, such features of design must be substantiated to reliably
operate by both ground tests and flight tests, as appropriate. Wear and rigging
tolerances should be considered in these demonstration tests.


                [The remainder of this page intentionally left blank.]





                                                         Page D – 39

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →