Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
b. Procedures.
(1) The reliability of the means for preventing ground resonance may be
substantiated as stated in the rule. An analysis report or a test proposal and
subsequent test report may be used to show compliance. The probable ranges of
damping restriction are an important part of the assessment. The test may be
conducted in conjunction with the testing required by § 27.241. See
paragraph AC 27.241.
(i) Analysis and tests may be used.
(ii) Reliable service history of identical or closely similar systems may be
used. The materials and fluids used, clearance or fits, seals, and physical installation
are important items to be evaluated and considered for “closely similar” systems.
(iii) Testing of the complete rotorcraft may be used to prove that
malfunction of a single means or member of the damping system will not cause ground
resonance. One method of demonstrating acceptable compliance is by removing all or
most of the fluid from a damper and considering the allowable ranges of damping of the
other parts of the rotorcraft damping system while operating the rotorcraft throughout
the rotor speed range from start to maximum rotor speed. Investigation of elastomeric
dampers may require innovative test procedures and preliminary discussions of these
prior to preparation of a test proposal. The rotorcraft cyclic control should be displaced
as noted in paragraph AC 27.241 of this document to assure that the possible rotorcraft
resonance frequencies are excited. If vibrations are damped in all tests, the damping
system is satisfactory. Each critical rotor damper and landing gear damper must
simulate a malfunction to comply with the rule. The testing discussed, however, could
be come very extensive if one were to attempt to test all combinations of all
maintenance adjustments of all components which contribute to the prevention of
ground resonance, while at the same time rendering each of the pertinent components
ineffective in turn and then repeating all of the maintenance tolerance testing each time.
Fortunately, rational analytical methods are available which will permit the evaluation of
such combinations so that only the combinations with the least amount of margin used
are physically tested.
(2) The pylon damper variation can affect ground resonance. The variations in
stiffness and/or damping of pylon mounts should be evaluated except the pylon mounts
on contemporary conventional rotorcraft may have little influence on “classical” ground
resonance stability. The dynamics of the rotorcraft on its landing gear is generally
established by the airframe properties and the landing gear properties under the
influence of the rotor system, with the “pylon” having little or no effect. For air or flight
resonance, the rotor generally couples with the rigid body modes of the fuselage. For a
specific design, a relatively simple analysis may be used to show the effect of the pylon
mount system stiffness on air and ground resonance stability, and if not important,
variations in the system may be omitted from the test program.
Page D - 34
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.